It doesn’t matter if it’s for your personal security, for roadworthiness testing or to avoid a fine, making sure your headlamp bulbs are constantly operational is necessary. In fact, bulbs are wearing parts that will undoubtedly burn out as time passes and as a result need to be replaced. You’re likely on this site because one of your parking lights is burnt out and you’re wondering how to change your hyundai getz’s license plate bulb, we’ve created this document to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your hyundai getz.
How to swap the license plate bulb on your hyundai getz coming from the outside
This approach is the least difficult of the two, in truth, for this one you will just need to remove the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will take some time on in the second section of this article content to demonstrate the approach.
So let’s begin with replacing the number plate bulb by going through the outside of your hyundai getz. It doesn’t matter if it’s the front or the back of your motor vehicle the operation will be identical.
Here are a few simple guidelines to stick to to carry out this maintenance tasks:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this goal (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your hyundai getz
- Use your screwdriver or knife to remove the bulb from its spot, in the event you are afraid of destroying anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to confirm the success of the operation.
.
How to replace the number plate bulb on your hyundai getz without outside access
Second section of our content page, change this license plate bulb on your hyundai getz without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my hyundai getz
To swap the one on the front plate, nothing could be simpler, you will have to position yourself under the motor vehicle (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take out the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to apply too much force or you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and replace it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my hyundai getz
Finally last solution, you must swap the bulb on the backplate of your hyundai getz, but you cannot open the cover from the outside of your motor vehicle. In this instance, here is the approach to execute this task:
- Unplug the battery from your hyundai getz
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your hyundai getz, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main solutions for replacing license plate bulbs on your car, take note that on some models the methodology may be a bit different but you should be able to realize it following the outline of this content page. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your hyundai getz. If you need to change other bulbs like the position light bulbs on your hyundai getz or the low beam bulbs on hyundai getz, don’t hesitate to read our content articles which explain you the process to follow.
If perhaps you have any further questions about the hyundai getz, do not hesitate to consult our hyundai getz category.
