Whether it’s for your own security, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are always working is very important. In reality, bulbs are wearing parts that will undoubtedly burn out after awhile and as a result need to be changed. You’re probably in this article because one of your parking lights is burnt out and you’re worried about how to change your Ford Crown Victoria’s license plate bulb, we’ve created this article content to help you do it on your own and not have to go to your mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Ford Crown Victoria.
How to swap the license plate bulb on your Ford Crown Victoria coming from the outside
This solution is the simplest of the two, in reality, for this one you will only have to remove the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will take a moment on in the second section of this content page to clarify the approach.
So let’s start with replacing the number plate bulb by going through the outside of your Ford Crown Victoria. Whether it’s the front or the back of your car the procedure will be the same.
Here are a few simple actions to stick to to carry out this routine service:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this goal (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ford Crown Victoria
- Use your screwdriver or knife to eject the bulb from its location, in the event you are afraid of breaking a thing, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the achievement of the process.
.
How to change the number plate bulb on your Ford Crown Victoria without outside access
Second section of our article, replace this license plate bulb on your Ford Crown Victoria without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Ford Crown Victoria
To swap the one on the front plate, nothing could be easier, you will have to put yourself under the car (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to apply too much force otherwise you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.
How to swap the rear license plate bulb on my Ford Crown Victoria
Finally last possibility, you must swap the bulb on the backplate of your Ford Crown Victoria, but you cannot open the cover from the outside of your car. In this case, here is the solution to conduct this task:
- Unplug the battery from your Ford Crown Victoria
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Ford Crown Victoria, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main tactics for replacing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to do it following the outline of this document. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Ford Crown Victoria. If you need to change other bulbs like the position light bulbs on your Ford Crown Victoria or the low beam bulbs on Ford Crown Victoria, don’t be reluctant to browse our articles which describe you the procedure to follow.
Whenever you have any further questions about the Ford Crown Victoria, do not hesitate to consult our Ford Crown Victoria category.
