It doesn’t matter if it’s for your own security, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are always functional is really important. In reality, bulbs are wearing parts that will obviously burn out in the future and therefore need to be changed. You’re most likely on this site because one of your parking lights is burnt out and you’re worried about how to change your Fiat Panda 3’s license plate bulb, we’ve created this content to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Fiat Panda 3.
How to replace the license plate bulb on your Fiat Panda 3 coming from the outside
This technique is the fastest of the two, actually, for this one you will simply have to remove the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second part of this content page to clarify the way.
So let’s start with changing the number plate bulb by going through the outside of your Fiat Panda 3. It doesn’t matter if it’s the front or the back of your automobile the technique will be similar.
Here are a few simple guidelines to stick to to carry out this service:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Fiat Panda 3
- Use your screwdriver or knife to remove the bulb from its place, in the event you are afraid of damaging something, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the successfulness of the procedure.
.
How to change the number plate bulb on your Fiat Panda 3 without outside access
Second part of our content page, replace this license plate bulb on your Fiat Panda 3 without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Fiat Panda 3
To replace the one on the front plate, nothing could be easier, you will have to position yourself under the automobile (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases held by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to exert too much pressure or you will break the plastic cover), and you will just have to remove the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Fiat Panda 3
Finally last option, you must replace the bulb on the backplate of your Fiat Panda 3, but you cannot open the cover from the outside of your automobile. In such a case, here is the solution to carry out this task:
- Unplug the battery from your Fiat Panda 3
- Locate the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Fiat Panda 3, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main approaches for changing license plate bulbs on your car, bear in mind that on some models the methodology may be a bit different but you should be able to accomplish it following the outline of this article content. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Fiat Panda 3. If you wish to change other bulbs like the position light bulbs on your Fiat Panda 3 or the low beam bulbs on Fiat Panda 3, don’t hesitate to read our content articles which describe you the process to follow.
To get more tips on the Fiat Panda 3, take a look at the Fiat Panda 3 category.
