Regardless it’s for your own safety, for roadworthiness testing or to avoid a fine, ensuring your headlamp bulbs are constantly functional is really important. In reality, bulbs are wearing auto parts that will inevitably burn out after a while and as a result need to be replaced. You’re almost certainly here because one of your parking lights is burnt out and you’re wondering how to change your Dodge Avenger’s license plate bulb, we’ve made this article content to help you do it on your own and not have to go to your mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Dodge Avenger.
How to change the license plate bulb on your Dodge Avenger throughout the outside
This option is the simplest of the two, in reality, for this one you will only require to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will take some time on in the second section of this content to explain the way.
So let’s start with replacing the number plate bulb by going through the outside of your Dodge Avenger. Regardless it’s the front or the back of your motor vehicle the technique will be identical.
Here are a few simple guidelines to stick to to perform this service:
- With the engine off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this intent (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Dodge Avenger
- Use your screwdriver or knife to eject the bulb from its spot, in the event that you are afraid of damaging a thing, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to validate the achievement of the operation.
.
How to replace the number plate bulb on your Dodge Avenger without outside access
Second section of our item, change this license plate bulb on your Dodge Avenger without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Dodge Avenger
To change the one on the front plate, nothing could be simpler, you will have to put yourself under the motor vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take out the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to exert too much pressure otherwise you will break the plastic cover), and you will only have to take out the burnt-out license plate bulb and swap it with the new , then check and reassemble the whole thing.
How to change the rear license plate bulb on my Dodge Avenger
Finally last option, you must change the bulb on the backplate of your Dodge Avenger, but you simply cannot open the cover from the outside of your motor vehicle. In such a case, here is the technique to conduct this operation:
- Disconnect the battery from your Dodge Avenger
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Dodge Avenger, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main approaches for replacing license plate bulbs on your car, take note that on some models the methodology may be a bit different but you should be able to realize it following the explanation of this content. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Dodge Avenger. If you want to change other bulbs like the position light bulbs on your Dodge Avenger or the low beam bulbs on Dodge Avenger, don’t hesitate to browse our articles which describe you the process to follow.
To find more tips on the Dodge Avenger, take a look at the Dodge Avenger category.
