Whether it’s for your specific security, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are in every case effective is really important. In reality, bulbs are wearing parts that will predictably burn out after awhile and therefore need to be replaced. You’re likely on this site because one of your parking lights is burnt out and you’re worried about how to change your Cadillac CT6’s license plate bulb, we’ve made this content to help you do it all on your own and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Cadillac CT6.
How to replace the license plate bulb on your Cadillac CT6 coming from the outside
This tactic is the simplest of the two, in reality, for this one you will just need to take away the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate a moment on in the second part of this content to explain the way.
So let’s begin with changing the number plate bulb by going through the outside of your Cadillac CT6. Whether it’s the front or the back of your automobile the method will be identical.
Here are a few simple guidelines to stick to to conduct this routine service:
- With the engine turned off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Cadillac CT6
- Use your screwdriver or knife to remove the bulb from its location, if you are worried of damaging a thing, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to confirm the successfulness of the operation.
.
How to change the number plate bulb on your Cadillac CT6 without outside access
Second part of our article, change this license plate bulb on your Cadillac CT6 without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Cadillac CT6
To replace the one on the front plate, nothing could be easier, you will have to put yourself under the automobile (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to put in too much force or you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Cadillac CT6
Finally last solution, you must replace the bulb on the backplate of your Cadillac CT6, but you simply cannot open the cover from the outside of your automobile. In this instance, here is the approach to conduct this task:
- Unplug the battery from your Cadillac CT6
- Locate the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Cadillac CT6, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main approaches for changing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to realize it following the outline of this content page. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Cadillac CT6. If you need to change other bulbs like the position light bulbs on your Cadillac CT6 or the low beam bulbs on Cadillac CT6, don’t hesitate to browse our articles which describe you the operation to follow.
If you have any additional questions about the Cadillac CT6, do not hesitate to consult our Cadillac CT6 category.
