Whether it’s for your specific safety, for roadworthiness testing or to avoid a fine, ensuring your headlamp bulbs are constantly functioning is very important. Indeed, bulbs are wearing units that will undoubtedly burn out with time and therefore need to be replaced. You’re probably on this site because one of your parking lights is burnt out and you’re questioning how to change your Buick Lucerne’s license plate bulb, we’ve written this document to help you do it by yourself and not have to go to your technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Buick Lucerne.
How to change the license plate bulb on your Buick Lucerne through the outside
This tactic is the easiest of the two, in fact, for this one you will simply have to remove the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will take a moment on in the second part of this content page to describe the method.
So let’s start with swapping the number plate bulb by going through the outside of your Buick Lucerne. Whether it’s the front or the back of your automobile the procedure will be the same.
Here are a few simple actions to follow to perform this maintenance:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Buick Lucerne
- Use your screwdriver or knife to eject the bulb from its location, in the event that you are scared of breaking a thing, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to validate the success of the process.
.
How to change the number plate bulb on your Buick Lucerne without outside access
Second part of our document, swap this license plate bulb on your Buick Lucerne without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Buick Lucerne
To change the one on the front plate, nothing could be less difficult, you will have to put yourself under the automobile (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to apply too much pressure otherwise you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and swap it with the new , then check and reassemble the whole thing.
How to change the rear license plate bulb on my Buick Lucerne
Finally last possibility, you must change the bulb on the backplate of your Buick Lucerne, but you are not able to open the cover from the outside of your automobile. In this case, here is the method to conduct this task:
- Disconnect the battery from your Buick Lucerne
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Buick Lucerne, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main techniques for swapping license plate bulbs on your car, be aware that on some models the method may be a bit different but you should be able to accomplish it following the explanation of this document. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Buick Lucerne. If you need to change other bulbs like the position light bulbs on your Buick Lucerne or the low beam bulbs on Buick Lucerne, don’t hesitate to browse our articles which demonstrate you the procedure to follow.
To find more tips on the Buick Lucerne, take a look at the Buick Lucerne category.
