It doesn’t matter if it’s for your own personal safety, for roadworthiness tests or to avoid a fine, ensuring your headlamp bulbs are always operational is really important. Indeed, bulbs are wearing units that will undoubtedly burn out in the future and consequently need to be replaced. You’re most certainly on the website because one of your parking lights is burnt out and you’re struggling with how to change your Acura MDX’s license plate bulb, we’ve created this content page to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Acura MDX.
How to change the license plate bulb on your Acura MDX through the outside
This process is the easiest of the two, in reality, for this one you will only require to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second section of this article to explain the way.
So let’s start with changing the number plate bulb by going through the outside of your Acura MDX. It doesn’t matter if it’s the front or the back of your automobile the operation will be the same.
Here are a few simple actions to follow to execute this maintenance tasks:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Acura MDX
- Use your screwdriver or knife to eject the bulb from its place, in the event you are afraid of damaging anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to validate the successfulness of the operation.
.
How to change the number plate bulb on your Acura MDX without outside access
Second section of our document, swap this license plate bulb on your Acura MDX without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Acura MDX
To change the one on the front plate, nothing could be less difficult, you will have to position yourself under the automobile (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to exert too much force otherwise you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and replace it with the new , then test out and reassemble the whole thing.
How to change the rear license plate bulb on my Acura MDX
Finally last possibility, you must change the bulb on the backplate of your Acura MDX, but you cannot open the cover from the outside of your automobile. In such a case, here is the tactic to carry out this task:
- Disconnect the battery from your Acura MDX
- Locate the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Acura MDX, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main ways for changing license plate bulbs on your car, take notice that on some models the technique may be a bit different but you should be able to do it following the explanation of this content page. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Acura MDX. If you desire to change other bulbs like the position light bulbs on your Acura MDX or the low beam bulbs on Acura MDX, don’t be reluctant to read our content articles which demonstrate you the process to follow.
If you want more tutorials on the Acura MDX, go to our Acura MDX category.
