Regardless whether it’s for your own security, for roadworthiness testing or to avoid a fine, being certain your headlamp bulbs are all the time operational is extremely important. In fact, bulbs are wearing units that will predictably burn out after a while and as a result need to be swapped out. You’re likely on the website because one of your parking lights is burnt out and you’re worried about how to change your Chrysler Town & Country’s license plate bulb, we’ve made this content to help you do it on your own and not have to go to your mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Chrysler Town & Country.
How to swap the license plate bulb on your Chrysler Town & Country coming from the outside
This process is the fastest of the two, in reality, for this one you will only need to remove the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second section of this document to explain the way.
So let’s start with changing the number plate bulb by going through the outside of your Chrysler Town & Country. Regardless whether it’s the front or the back of your car the operation will be identical.
Here are a few simple steps to stick to to execute this service:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this purpose (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chrysler Town & Country
- Use your screwdriver or knife to eject the bulb from its placement, in the event that you are scared of destroying something, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to confirm the success of the process.
.
How to replace the number plate bulb on your Chrysler Town & Country without outside access
Second section of our article, replace this license plate bulb on your Chrysler Town & Country without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Chrysler Town & Country
To swap the one on the front plate, nothing could be simpler, you will have to put yourself under the car (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Remove the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to exert too much pressure or you will break the plastic cover), and you will just have to remove the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to swap the rear license plate bulb on my Chrysler Town & Country
Finally last possibility, you must swap the bulb on the backplate of your Chrysler Town & Country, but you cannot open the cover from the outside of your car. In this instance, here is the approach to carry out this operation:
- Unplug the battery from your Chrysler Town & Country
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Chrysler Town & Country, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main methods for changing license plate bulbs on your car, be aware that on some models the method may be a bit different but you should be able to realize it following the outline of this article content. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Chrysler Town & Country. If you need to change other bulbs like the position light bulbs on your Chrysler Town & Country or the low beam bulbs on Chrysler Town & Country, don’t hesitate to consult our articles which demonstrate you the procedure to follow.
If perhaps you have any further questions about the Chrysler Town & Country, do not hesitate to consult our Chrysler Town & Country category.
