If you’re a bit of a do-it-yourselfer, you’re probably wanting to manage the majority of the maintenance to be achieved on your Bmw Serie 6, but some are more complex than others and need the removal of body parts or parts to access the component you want to operate on. We would like to help you in this process. That’s why in this article we are going to discover how to remove the bumper from a Bmw Serie 6. This task is not very complex and you should have the ability to do it with few tools. To accomplish this, first we will see how to remove the front bumper of your Bmw Serie 6, then how to remove the rear bumper of this one.
How to remove the front bumper from a Bmw Serie 6
So let’s start our content page with the front bumper of your Bmw Serie 6. To take it off, you will just need a set of ratchet wrenches, some screwdrivers and torx bits. Here are the guidelines you will have to follow in order to disassemble the bumper of your Bmw Serie 6 in good conditions:
- If you want to be more comfy, we advise you to put your Bmw Serie 6 on stands and to remove the front wheels to have a perfect access to the whole front bumper.
- Open the bonnet of your vehicle: Would seem obvious, but you will need to have access to the bumper attachment in your engine compartment.
- Take out the wheel arches: They’re also referred to as fenders, but they’ll get in the way and prevent you from accessing all the screws on the front bumper of your Bmw Serie 6. Depending on your vehicle features and the year of your model, you will also be able to find staples, to accomplish this, you will just have to use a staple extractor or to do it gently with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is behind your mudguard and that fastens the front bumper of your Bmw Serie 6 on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine bay.
- Now it’s time to go beneath your Bmw Serie 6 to unscrew the bolts that are on the chassis of the vehicle, you will find some in the middle of the bumper and on the sides.
- Remember to unplug the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you almost certainly forgot a screw or a clip. Think of employing a carpet or other to prevent that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Bmw Serie 6, to reassemble it follow the steps in the opposite way.
How to remove the rear bumper from a Bmw Serie 6
And now, regardless if the process is quite equivalent, we will take a look at the case of removing the rear bumper from your Bmw Serie 6. For each stage to avoid repeating ourselves we will just give you the broad highlights, refer to part 1 if you have any uncertainties or questions for more info.
- Start with undertaking the same first stage, that is, lift your Bmw Serie 6 and take out your rear wheels in order to have an optimal working area to remove the bumper of your Bmw Serie 6 serenely
- Remove the rear wheel arches of your Bmw Serie 6 to access the side bumper side brackets
- Open your trunk
- Take out the side brackets in your wheel arches to make it easier to remove the bumper from your Bmw Serie 6.
- Take off the lower bindings underneath your Bmw Serie 6.
- While doing so, make sure disconnect the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Bmw Serie 6, follow the same technique as for the front bumper
Here, you have discoverd through these two parts, how to remove the bumper from a Bmw Serie 6 whether it is the front one or the rear one the approaches are practically the same and it is enough to be meticulous to make everything go well.
To get more tips on the Bmw Serie 6, take a look at the Bmw Serie 6 category.
