If you’re a bit of a handy person, you’re quite likely wanting to take care of the vast majority of the work to be done on your Audi Q2, but some are more complex than others and require the removal of body parts or components to access the component you want to focus on. We want to help you in this process. That’s why on this web page we are going to find out how to remove the bumper from a Audi Q2. This action is not very complex and you should be able to do it with few equipment. For that, first we will discover how to remove the front bumper of your Audi Q2, then how to remove the rear bumper of this one.
How to remove the front bumper from a Audi Q2
So let’s start our content page with the front bumper of your Audi Q2. To remove it, you will just require a set of ratchet wrenches, some screwdrivers and torx bits. Here are the guidelines you will have to follow in order to disassemble the bumper of your Audi Q2 in good conditions:
- If you want to be more comfy, we advise you to put your Audi Q2 on stands and to remove the front wheels to have a good access to the whole front bumper.
- Open the bonnet of your automobile: Seems obvious, but you will need to have access to the bumper attachment in your engine compartment.
- Remove the wheel arches: They’re also known as fenders, but they’ll get in the way and prevent you from accessing all the screws on the front bumper of your Audi Q2. According to your motor vehicle features and the year of your model, you will also be able to find staples, to achieve this, you will just have to use a staple extractor or to do it gently with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is from behind your mudguard and that locks the front bumper of your Audi Q2 on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine compartment.
- Now it’s time to go under your Audi Q2 to unscrew the bolts that are on the chassis of the motor vehicle, you will find some in the middle of the bumper and on the sides.
- Be sure you disconnect the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you almost certainly forgot a screw or a clip. Think of using a carpet or other to prevent that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Audi Q2, to put it back in place follow the steps in the opposite direction.
How to remove the rear bumper from a Audi Q2
And to finish, regardless if the operation is quite equivalent, we will check out the case of removing the rear bumper from your Audi Q2. For each step to avoid repeating ourselves we will just give you the broad outlines, refer to part 1 if you have any uncertainties or questions for more info.
- Start with executing the same first step, that is, lift your Audi Q2 and take out your rear wheels in order to have an ideal working space to remove the bumper of your Audi Q2 without trouble
- Remove the rear wheel arches of your Audi Q2 to access the side bumper side brackets
- Open your trunk
- Remove the side brackets in your wheel arches to make it easier to remove the bumper from your Audi Q2.
- Take out the lower bindings below your Audi Q2.
- While doing so, make sure disconnect the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Audi Q2, follow the same process as for the front bumper
Here, you have discoverd through these two parts, how to remove the bumper from a Audi Q2 whether it is the front one or the rear one the ways are more or less the same and it is enough to be meticulous to make everything go well.
If you need more guides on the Audi Q2, go to our Audi Q2 category.
