You’ve most likely already been aware of the popular EGR valve, the anti-pollution valve. It is not usually appreciated by drivers because it is likely to create more concerns than anything else… Actually, dependant upon the use you are going to make of your car, it can become clogged and trigger you a lot of problems. If this is the case, you are most likely concerned about how to clean the EGR valve of your Ford F 250 ? Don’t worry, we’ve written this article content to help you with this operation. To achieve this, we will first check out the intent of the EGR valve, then what are the failures that the EGR valve of your Ford F 250 can bring on and at last the section that will most likely appeal you the most, how to clean the EGR valve Ford F 250?
How to Clean your Ford F 250 EGR Valve: Role and Operation
Goal of the EGR valve
The EGR valve of your car has been added to diesel engines mostly to reduce pollution emitted by automobiles and to meet EURO requirements on Ford F 250 . It will as a result influence the quality of exhaust gas output and get rid of toxic particles, mainly Nitrogen Oxide.
Operation of the EGR valve
Before we discover how to clean the EGR valve on your Ford F 250 , we will take a look at how it functions. As seen just before, its objective is to clean the exhaust fumes, so it will be placed at the engine outlet, thanks to a valve, it will be able to return the unburned exhaust gases to the engine for a second burn which will get rid of all unburned toxic particles. It will perform mainly at low speed because at high speed the combustion is enough to burn all these gases.
How to clean your Ford F 250 EGR valve: Identifying faults
The EGR valve, although very effective to limit the pollution emissions of your Ford F 250 , will unfortunately tend to clog up because of soot/gas deposits that will accumulate in its mechanism, which will eventually risk blocking the operation of the valve, until entirely blocking the engine unit, here are the signs of illness that a defective EGR valve on your Ford F 250 can bring about:
- Motor light on
- Power loss
- Technical inspection refused
- Black gases
- Vehicle that grazes at low speed
- Low RPM settings
How to clean your Ford F 250 EGR valve: In practice
And now we’ll start the section you are most intrigued by, how to clean the EGR valve of your car. Here are the two solutions that you can use.
Do it on your own
How to clean your Ford F 250 EGR valve system: Without taking it apart
Despite the fact this procedure is less efficient, it is however possible to consider a “rough” cleaning of your EGR valve, the truth is, you will only need to use fuel additives, similar to the products used to clean the injection. These particular solutions must be injected into the running engine, at the right operating temperature, diluted in about 20 litres of fuel and run the engine for 3 or 4 minutes in high rev to clean the EGR valve of your Ford F 250.
How to clean your car EGR valve: With disassembly
Here is the most effective procedure, which will require enough access to the EGR valve to carry out the treatment on your own. If so, the operation is fairly straightforward. You will need to disconnect the electromagnet from the EGR valve, remove the few screws that hold it in place, and remove it. Once these steps are done, now comes the time for cleaning. To accomplish this, you will need to use a product such as solvent, petrol, oven cleaning product, which you will leave to act for ten minutes, then scrape off the rest using a scraper, finish cleaning with wire brush. If you want to go further, you can as well clean the two canal on which it is connected which may be scorched, for this, use a scraper and a vacuum cleaner to avoid dropping deposits in the conduits. You will only have to reassemble it and you will have finished cleaning the EGR valve of your Ford F 250.
Have it done by a professional
If, your EGR valve is not accessible because of the series or the engine of your car and if removing it would cause too many problems (removing too many elements that hinder access for example), how to clean the EGR valve of your Ford F 250? In cases like this, it would be better rather than launching yourself into an overly complex operation, you turn to an auto mechanic. He will be able to carry out the job more cleanly and will be able, if required, to change the valve if it is dead. The cost of cleaning dependant upon the difficulty of access is between 70 and 300 €.
Remove the EGR valve of your Ford F 250
Finally, a number of people make a more radical decision to limit the risk of a failed valve. Instead of cleaning the EGR valve of their Ford F 250, they just choose to block it in the closed position. This treatment will have the result of greatly increasing the pollution emitted by the car, of no longer complying with pollution requirements, of having an engine warning light permanently on and in the end risk fouling the engine. We strongly recommend against making this choice. If you have other questions or want to learn more about your car, don’t be reluctant to take a look at our dedicated page.
If you wish more tutorials on the Ford F 250, go to our Ford F 250 category.
