Regardless it’s for your own safety, for roadworthiness testing or to avoid a fine, ensuring your headlamp bulbs are always functional is very important. Indeed, bulbs are wearing units that will inevitably burn out after some time and as a consequence need to be replaced. You’re quite likely on this site because one of your parking lights is burnt out and you’re wondering how to change your Volkswagen Rabbit’s license plate bulb, we’ve written and published this article to help you do it all on your own and not have to go to your auto technician. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Volkswagen Rabbit.
How to swap the license plate bulb on your Volkswagen Rabbit throughout the outside
This process is the fastest of the two, actually, for this one you will just have to take off the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second part of this content page to describe the method.
So let’s start with replacing the number plate bulb by going through the outside of your Volkswagen Rabbit. Regardless it’s the front or the back of your automobile the technique will be identical.
Here are a few simple guidelines to stick to to execute this routine service:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this purpose (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Volkswagen Rabbit
- Use your screwdriver or knife to eject the bulb from its spot, if you are scared of damaging something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to confirm the successfulness of the procedure.
.
How to change the number plate bulb on your Volkswagen Rabbit without outside access
Second part of our content page, swap this license plate bulb on your Volkswagen Rabbit without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Volkswagen Rabbit
To swap the one on the front plate, nothing could be less complicated, you will have to position yourself under the automobile (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly held by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to apply too much pressure otherwise you will break the plastic cover), and you will just have to take off the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.
How to swap the rear license plate bulb on my Volkswagen Rabbit
Finally last possibility, you must swap the bulb on the backplate of your Volkswagen Rabbit, but you cannot open the cover from the outside of your automobile. In this instance, here is the tactic to accomplish this task:
- Disconnect the battery from your Volkswagen Rabbit
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Volkswagen Rabbit, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main tactics for replacing license plate bulbs on your car, remember that on some models the methodology may be a bit different but you should be able to accomplish it following the outline of this content. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Volkswagen Rabbit. If you desire to change other bulbs like the position light bulbs on your Volkswagen Rabbit or the low beam bulbs on Volkswagen Rabbit, don’t be reluctant to consult our content articles which describe you the operation to follow.
In the event that you have any additional questions about the Volkswagen Rabbit, do not hesitate to consult our Volkswagen Rabbit category.
