Regardless whether it’s for your personal safety, for roadworthiness testing or to avoid a fine, making sure your headlamp bulbs are always functioning is very important. In reality, bulbs are wearing units that will undoubtedly burn out after awhile and therefore need to be replaced. You’re most certainly in this article because one of your parking lights is burnt out and you’re worried about how to change your GMC Yukon’s license plate bulb, we’ve written this document to help you do it without any help and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your GMC Yukon.
How to swap the license plate bulb on your GMC Yukon through the outside
This method is the quickest of the two, in fact, for this one you will just need to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will take a moment on in the second section of this document to show you the way.
So let’s begin with swapping the number plate bulb by going through the outside of your GMC Yukon. Regardless whether it’s the front or the back of your motor vehicle the technique will be the same.
Here are a few simple steps to follow to execute this routine service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your GMC Yukon
- Use your screwdriver or knife to remove the bulb from its place, if you are afraid of breaking anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to validate the achievement of the process.
.
How to replace the number plate bulb on your GMC Yukon without outside access
Second section of our content, replace this license plate bulb on your GMC Yukon without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my GMC Yukon
To swap the one on the front plate, nothing could be less complicated, you will have to position yourself under the motor vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to apply too much pressure or you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.
How to swap the rear license plate bulb on my GMC Yukon
Finally last possibility, you must swap the bulb on the backplate of your GMC Yukon, but you cannot open the cover from the outside of your motor vehicle. In this case, here is the tactic to do this task:
- Disconnect the battery from your GMC Yukon
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your GMC Yukon, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main approaches for swapping license plate bulbs on your car, remember that on some models the methodology may be a bit different but you should be able to realize it following the explanation of this article content. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your GMC Yukon. If you need to change other bulbs like the position light bulbs on your GMC Yukon or the low beam bulbs on GMC Yukon, don’t be reluctant to read our content articles which demonstrate you the process to follow.
If you want more guides on the GMC Yukon, go to our GMC Yukon category.
