Whether it’s for your own personal safety, for roadworthiness testing or to avoid a fine, making sure your headlamp bulbs are all the time effective is very important. In reality, bulbs are wearing units that will predictably burn out over time and consequently need to be replaced. You’re most likely here because one of your parking lights is burnt out and you’re worried about how to change your Acura TL’s license plate bulb, we’ve created this document to help you do it on your own and not have to go to your auto technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Acura TL.
How to replace the license plate bulb on your Acura TL throughout the outside
This option is the least difficult of the two, in reality, for this one you will just need to take off the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second part of this content page to teach you the way.
So let’s begin with swapping the number plate bulb by going through the outside of your Acura TL. Whether it’s the front or the back of your motor vehicle the procedure will be identical.
Here are a few simple steps to follow to conduct this maintenance:
- With the engine turned off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Acura TL
- Use your screwdriver or knife to eject the bulb from its placement, if you are worried of breaking something, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to validate the successfulness of the procedure.
.
How to change the number plate bulb on your Acura TL without outside access
Second part of our content, change this license plate bulb on your Acura TL without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Acura TL
To replace the one on the front plate, nothing could be less complicated, you will have to put yourself under the motor vehicle (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to apply too much pressure otherwise you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Acura TL
Finally last possibility, you must replace the bulb on the backplate of your Acura TL, but you are not able to open the cover from the outside of your motor vehicle. In such a case, here is the method to do this task:
- Disconnect the battery from your Acura TL
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Acura TL, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main tactics for swapping license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to do it following the explanation of this content. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Acura TL. If you need to change other bulbs like the position light bulbs on your Acura TL or the low beam bulbs on Acura TL, don’t hesitate to browse our articles which describe you the process to follow.
To get more tips on the Acura TL, take a look at the Acura TL category.
