When your car is running normally everything is fine, however if it starts to have frequent problems you may possibly start to worry, especially if your car won’t start. In this article we will learn you where the starter of a Mazda CX 30 is, it will help you to solve your ignition problems. To achieve this, we will first explain the purpose of a starter, then, where is the starter on a Mazda CX 30 , and, finally, how to replace the starter of a car.

find-starter-mazada-cx-30

Role of the starter on your Mazda CX 30

We start this content by detailing the purpose of the starter motor on your Mazda CX 30. The starter is an electric motor which is powered by your battery, its role will be to make your engine run at a high enough speed to start it (usually around 300/400 rpm). It is consisting of three most important parts:

  • The Solenoid: This part is an electrical relay that will work as a switch, it will be activated by the key of your Mazda CX 30 and let the current from your battery to the engine unit of your alternator.

    • The engine unit: Main component of your alternator, it is the one that will drive the flywheel of your Mazda CX 30 and create enough speed for your engine unit to start.

  • The engagement pinion: This is the last part of your starter, it is the toothed wheel that will be in direct contact with the flywheel, it enables to transfer the force from the starter to the engine.

Where is the starter on a Mazda CX 30?

Now that we have quickly detailed what a starter is and how it works, we will answer the question that most of you have to ask yourselves where is the starter located on a Mazda CX 30? It is quite easy to find a starter, in fact, it is a large part that will almost always be positioned in a similar location. We let you discover the two possible locations for your car starter below.

Location of the starter on classic Mazda CX 30

First and most general case, where to find the starter of a Mazda CX 30 with a conventional motor (implied without start and stop). The starter has a particular objective, to start the engine unit of your car, for that, it must always be near the engine unit flywheel of this one because it is the part that it actuates when it is used. The flywheel is located at the junction between your gearbox and your engine unit.

Location of the starter to Mazda CX 30 with start and stop

And now second possible starter location of your Mazda CX 30 . This case is much less frequent. It only is about engines fitted with start and stop, and a good part of them will be equipped with a starter positioned close to the flywheel. Nevertheless, on some particular series or engines, the starter of your Mazda CX 30 might be built in in your alternator, it is then called a starter-alternator, to find it nothing much easier, find your accessory belt and you should find out the big starter block.

How to replace the starter on a Mazda CX 30?

Finally, we’ll show you to you quite quickly how to replace the starter of a Mazda CX 30. This process is not necessarily complex, it can be considered by people who have a minimum of basic mechanical expertise and adapted tools. Stick to below the most important steps to carry out this intervention:

  • Disconnect the battery on your Mazda CX 30, if you don’t know how to do it, don’t hesitate to seek advice from our content which details how to do it without taking any risk.
  • After discovering your starter, loosen the fasteners that hold it in your engine unit block, there will usually be 2 or 3

    • .

  • It will be time to disconnect the power cables from the starter motor of your Mazda CX 30, however before doing so we recommend you to take a picture of the set up to avoid making a mistake when reassembling.
  • It’s possible that to remove it you may possibly need to remove auto parts like the gimbal.
  • Remount the new starter, being careful when connecting the connectors.
  • Reconnect your battery and test your starter.

If you wish more guides on the Mazda CX 30, go to our Mazda CX 30 category.