The safety of a car is very important. Even if the Mazda 5 are financial holes, certain maintenance acts are fundamental. Today we will explain to you when to replace the brake discs of your Mazda 5? To achieve this, to begin with, we will find out what the brake discs of your motor vehicle are used for, then, when to replace the brake discs of your Mazda 5, and, finally, how to change them with new ones.

change-brake-discs-mazda-5

Benefit of the brake discs of a Mazda 5

We start our content page by detailing what the brake discs of a Mazda 5 are used for, it will enable you to figure out why it is important to make certain that they are always in good working conditions.
Brake discs are the main part of your braking system. In truth, braking on an Mazda 5 is hydraulic, it is a system of hoses and pressurized oil that will come into action when you press your brake pedal. This pressure will actuate a piston that will push the brake pads on your brake disc which is attached to your wheel. When the brake pads will pinch the discs which will trigger your Mazda 5 to brake.

When to replace the brake discs of a Mazda 5?

We will now move on to the section that certainly attracts you to this content, namely, when changing the brake discs of a Mazda 5? How we explained it to you just before, the brake discs and pads work in osmosis, nevertheless these two components are wearing auto parts and they will, over time and specifically the friction when braking wears out and loses braking power. We will now highlight the different solutions to know when to change them:

  • We consider that generally speaking the brake discs should be changed every 80, 000 – 100, 000 km on a Mazda 5 , nevertheless it is important to know that dependent on your driving style and the type of journey this can change considerably. In fact, if you principally drive on the motorway and your brakes are only slightly used, this value can increase, on the other hand, if you only drive in built-up areas, it can reduce.
  • A simple and successful way to find out the state of the brake discs on your car is during the technical inspection. In fact this thorough control checks the state of your brakes and the controller will tell you if they are in good state or need to be changed.
  • A simple visual way to know when to replace the brake discs on your Mazda 5 is to remove the wheels after the vehicle has been set on stands. Once taken off, you will be able to access your discs and verify their state. If they have any big scratches or deformations you will have to replace them. Otherwise the second indicator to verify is to measure the depth of the disk in relation to its edge, if this value exceeds 1 mm you will have to change them by new ones.

.

How to replace the brake discs on your Mazda 5?

Finally, to conclude this content we will quickly show you how to replace the brake discs of your Mazda 5. You must know that if you replace the brake discs of your car, you will absolutely have to change the brake pads of your Mazda 5, don’t think twice to seek advice from our content which teaches you how to make this replace.
As far as changing discs is concerned, here are the main steps to stick to:

  • Put your Mazda 5 on stands, take off the wheels you want to work on.
  • Using a large flat screwdriver, pry on your brake pads to compress the caliper piston as much as possible and have enough play to make all your changes.
  • Using large Torx bits, take out the two nuts that lock the upper part of your brake caliper, take out it.
  • Remove your brake pads, then unlock your brake discs thanks to the two torx screws on the side of the disc, you might need a mallet to remove the discs.
  • Replace the discs and tighten them with the new torx screws provided, replace your pads, reassemble the upper part of the caliper and tighten everything tightly.
  • Mounting your wheels, and remember to do a 500-kilometer brake break-in before braking hard.

If perhaps you have any further questions about the Mazda 5, do not hesitate to consult our Mazda 5 category.