The safety of a motor vehicle is essential. Even if the Mazda 2 are economic holes, certain routine service works are essential. Today we will explain to you when to replace the brake discs of your Mazda 2? To accomplish this, to begin with, we will see what the brake discs of your car are used for, then, when to replace the brake discs of your Mazda 2, and, finally, how to replace them with new ones.
Benefit of the brake discs of a Mazda 2
We begin our article by explaining what the brake discs of a Mazda 2 are used for, it will enable you to figure out why it is necessary to ensure that that they are always in good working order.
Brake discs are the most important part of your braking system. Indeed, braking on an Mazda 2 is hydraulic, it is a system of hoses and pressurized oil that will come into action when you press your brake pedal. This pressure will actuate a piston that will push the brake pads on your brake disc which is attached to your wheel. When the brake pads will pinch the discs which will bring about your Mazda 2 to brake.
When to replace the brake discs of a Mazda 2?
We will now move on to the part that most certainly attracts you to this content, namely, when changing the brake discs of a Mazda 2? How we described it to you just before, the brake discs and pads work in osmosis, however these two components are wearing parts and they will, as time passes and specifically the friction when braking wears out and loses braking power. We will now highlight the different methods to know when to replace them:
- We consider that generally speaking the brake discs should be changed every 80, 000 – 100, 000 km on a Mazda 2 , however it is necessary to know that dependent on your driving style and the type of journey this can vary substantially. In truth, if you mainly drive on the motorway and your brakes are only slightly used, this amount can increase, on the other hand, if you only drive in built-up areas, it can reduce.
- A simple and successful technique to identify the condition of the brake discs on your motor vehicle is during the technical inspection. In truth this thorough control checks the state of your brakes and the controller will tell you if they are in good condition or need to be changed.
- A basic visual technique to know when to replace the brake discs on your Mazda 2 is to remove the wheels after the car has been set on stands. Once taken out, you will be able to access your discs and verify their condition. If they have any big scratches or deformations you will have to replace them. In any other case the second indicator to check is to measure the depth of the disk in relation to its edge, if this value exceeds 1 mm you will have to change them by new ones.
.
How to replace the brake discs on your Mazda 2?
Finally, to end this content we will quickly explain how to replace the brake discs of your Mazda 2. You must know that if you replace the brake discs of your motor vehicle, you will absolutely have to change the brake pads of your Mazda 2, don’t hesitate to consult our content which explains you how to make this replace.
As far as changing discs is concerned, here are the most important steps to stick to:
- Put your Mazda 2 on stands, take off the wheels you want to work on.
- Using a large flat screwdriver, pry on your brake pads to compress the caliper piston as much as possible and have enough play to make all your changes.
- Using large Torx bits, remove the two nuts that lock the upper part of your brake caliper, remove it.
- Take out your brake pads, then unlock your brake discs thanks to the two torx screws on the side of the disc, you might need a mallet to remove the discs.
- Replace the discs and tighten them with the new torx screws provided, replace your pads, reassemble the upper part of the caliper and tighten everything tightly.
- Mounting your wheels, and make sure to do a 500-kilometer brake break-in before braking hard.
If you need more tutorials on the Mazda 2, go to our Mazda 2 category.
