The safety of a motor vehicle is very important. Even if the Fiat Panda 3 are economic holes, certain routine service works are essential. Today we will explain to you when to replace the brake discs of your Fiat Panda 3? To achieve this, first of all, we will find out what the brake discs of your car are used for, then, when to replace the brake discs of your Fiat Panda 3, and, finally, how to replace them with new ones.
Interest of the brake discs of a Fiat Panda 3
We start our article content by detailing what the brake discs of a Fiat Panda 3 are used for, it will enable you to figure out why it is necessary to be sure that they are always in good working order.
Brake discs are the main part of your braking system. Obviously, braking on an Fiat Panda 3 is hydraulic, it is a system of hoses and pressurized oil that will come into action when you press your brake pedal. This pressure will actuate a piston that will push the brake pads on your brake disc which is attached to your wheel. When the brake pads will pinch the discs which will cause your Fiat Panda 3 to brake.
When to replace the brake discs of a Fiat Panda 3?
We will now move on to the part that undoubtedly attracts you to this content, namely, when replacing the brake discs of a Fiat Panda 3? How we revealed it to you just before, the brake discs and pads work in osmosis, however these two elements are wearing parts and they will, after some time and especially the friction when braking wears out and loses braking power. We will now highlight the different methods to know when to replace them:
- We consider that in general the brake discs should be changed every 80, 000 – 100, 000 km on a Fiat Panda 3 , however it is necessary to know that according to your driving style and the type of journey this can vary substantially. In truth, if you mainly drive on the motorway and your brakes are only slightly used, this value can increase, on the other hand, if you only drive in built-up areas, it can decrease.
- A simple and effective technique to find out the state of the brake discs on your motor vehicle is during the technical inspection. In truth this thorough control checks the state of your brakes and the controller will tell you if they are in good state or need to be changed.
- A basic visual technique to know when to replace the brake discs on your Fiat Panda 3 is to remove the wheels after the vehicle has been set on stands. Once taken off, you will have the ability to access your discs and check their state. If they have any big scratches or deformations you will have to replace them. Otherwise the second indicator to verify is to measure the depth of the disk in relation to its edge, if this value exceeds 1 mm you will have to change them by new ones.
.
How to replace the brake discs on your Fiat Panda 3?
Finally, to end this content we will fairly quickly explain how to replace the brake discs of your Fiat Panda 3. You must know that if you replace the brake discs of your motor vehicle, you will absolutely have to change the brake pads of your Fiat Panda 3, don’t think twice to seek advice from our content which points out you how to make this replace.
As far as changing discs is concerned, here are the main steps to follow:
- Put your Fiat Panda 3 on stands, take off the wheels you want to work on.
- Using a large flat screwdriver, pry on your brake pads to compress the caliper piston as much as possible and have enough play to make all your changes.
- Using large Torx bits, remove the two nuts that lock the upper part of your brake caliper, remove it.
- Take out your brake pads, then unlock your brake discs thanks to the two torx screws on the side of the disc, you may need a mallet to remove the discs.
- Replace the discs and tighten them with the new torx screws provided, replace your pads, reassemble the upper part of the caliper and tighten everything tightly.
- Mounting your wheels, and remember to do a 500-kilometer brake break-in before braking hard.
If you wish more tutorials on the Fiat Panda 3, go to our Fiat Panda 3 category.
