The safety of a motor vehicle is essential. Whether or not the CUPRA FORMENTOR are financial holes, certain routine service acts are fundamental. In this article we will explain to you when to change the brake discs of your CUPRA FORMENTOR? To get this done, to begin with, we will discover what the brake discs of your motor vehicle are used for, then, when to change the brake discs of your CUPRA FORMENTOR, and, finally, how to replace them with new ones.

change-brake-discs-cupra-formentor

Benefit of the brake discs of a CUPRA FORMENTOR

We begin our article by explaining what the brake discs of a CUPRA FORMENTOR are used for, it will allow you to figure out why it is essential to ensure that that they are constantly in good working order.
Brake discs are the most important component of your braking system. In fact, braking on an CUPRA FORMENTOR is hydraulic, it is a system of hoses and pressurized oil that will come into action when you press your brake pedal. This pressure will actuate a piston that will push the brake pads on your brake disc which is attached to your wheel. When the brake pads will pinch the discs which will cause your CUPRA FORMENTOR to brake.

When to change the brake discs of a CUPRA FORMENTOR?

We will now move on to the part that most certainly attracts you to this content, namely, when changing the brake discs of a CUPRA FORMENTOR? How we described it to you just before, the brake discs and pads work in osmosis, however these two components are wearing auto parts and they will, with time and especially the friction when braking wears out and loses braking power. We will now detail the different solutions to know when to replace them:

  • We consider that in general the brake discs should be changed every 80, 000 – 100, 000 km on a CUPRA FORMENTOR , however it is essential to know that according to your driving style and the type of journey this can vary significantly. In truth, if you mainly drive on the motorway and your brakes are only slightly used, this value can increase, alternatively, if you only drive in built-up areas, it can decrease.
  • A basic and good way to identify the state of the brake discs on your motor vehicle is during the technical inspection. In truth this thorough control checks the state of your brakes and the controller will tell you if they are in good state or need to be changed.
  • A very easy visual way to know when to change the brake discs on your CUPRA FORMENTOR is to remove the wheels after the vehicle has been set on stands. Once removed, you will be able to access your discs and check their state. If they have any big scratches or deformations you will have to change them. In any other case the second indicator to check is to measure the depth of the disk in relation to its edge, if this value exceeds 1 mm you will have to change them by new ones.

.

How to change the brake discs on your CUPRA FORMENTOR?

Finally, to conclude this content we will fairly quickly describe how to change the brake discs of your CUPRA FORMENTOR. You must know that if you change the brake discs of your motor vehicle, you will absolutely have to change the brake pads of your CUPRA FORMENTOR, don’t hesitate to seek advice from our content which explains you how to make this change.
As far as changing discs is concerned, here are the most important steps to stick to:

  • Put your CUPRA FORMENTOR on stands, take off the wheels you want to work on.
  • Using a large flat screwdriver, pry on your brake pads to compress the caliper piston as much as possible and have enough play to produce all your changes.
  • Using large Torx bits, take out the two nuts that lock the upper component of your brake caliper, take out it.
  • Take out your brake pads, then unlock your brake discs thanks to the two torx screws on the side of the disc, you may need a mallet to remove the discs.
  • Replace the discs and tighten them with the new torx screws provided, change your pads, reassemble the upper component of the caliper and tighten everything tightly.
  • Mounting your wheels, and remember to do a 500-kilometer brake break-in before braking hard.

To discover more tips on the CUPRA FORMENTOR, take a look at the CUPRA FORMENTOR category.