Contemporary automobiles have an increasing number of functionnalities and although they give us a lot of comfort, some of them are not always simple to use. No matter you have rented a car, been lent one, or just bought a Peugeot Partner Tepee, depending on its functionnalities, it can be complicated to figure out how to start a Peugeot Partner Tepee? Even if this imperative act of running a car may seem very clear to many of you, dependent on the options and the year of production of your car, it will be more or less simple to do so. In this article we will demonstrate the different procedures to start a Peugeot Partner Tepee with the key, then, in a second section, how to switch on a Peugeot Partner Tepee with a card, and to finish, without using the key.
How to start a Peugeot Partner Tepee with key?
So we commence our article content which is meant to teach you how to start a Peugeot Partner Tepee, which is equipped with a classic key start. Find under the different measures to be executed to turn on the engine of your Peugeot Partner Tepee:
- Distinguish the position of the neiman (hole in which the key is introduced), it is most of the time on the right side of your steering wheel, on the dash. If your steering wheel is blocked, do not think twice to browse our article content on the steering wheel blocked on Peugeot Partner Tepee that is blocked to learn how to unblock it.
- Place the key into this one.
- Check that you are in neutral for a manual car and in the “N” or “P” position for an automatic transmission.
- Turn the ignition on by turning it clockwise a quarter turn up to the point you feel you’ve passed the first notch.
- Check on your dashboard that the orange lights go out, if you don’t know what they indicate don’t think twice to browse our article content on orange lights on Peugeot Partner Tepee to find out the explanation for this.
- You just have to go one more notch clockwise and hold it in the stop until your Peugeot Partner Tepee starts (do not let your starter run more than 10 seconds or you risk injuring it, if the car does not start, let it recover a few tens of seconds before a new testing)
- That’s it. You managed to start your Peugeot Partner Tepee,
.
How to start a Peugeot Partner Tepee with the key card?
After learning about how to turn on the engine of a Peugeot Partner Tepee with key or will explain you how to do it for a Peugeot Partner Tepee equipped with a key card and not a key. The method remains roughly the same, so don’t think twice to return to the previous part to get details on each of the steps to do. Learn down below the steps to adhere to to start your Peugeot Partner Tepee with a card:
- Depending on the year and the series, you may or may not need to put in the card in a specific slot, verify on your dashboard if your Peugeot Partner Tepee is equipped with this slot or not.
- If it has one, insert the card in this hole, or you can keep the card on you or anywhere in the cabin.
- Locate the “start” button, which is in most cases located at steering wheel height close to the classic neiman location, otherwise it is in most cases situated on the centre console.
- Check that you’re in neutral or neutral on an automatic transmission.
- Push the “start” button once to turn on the ignition of your Peugeot Partner Tepee
- Push a second time after a few seconds or extinction of the orange lights on your dashboard to start your Peugeot Partner Tepee
.
.
How do I start a Peugeot Partner Tepee without a key?
And to finish, we will find out, how to start a Peugeot Partner Tepee without a key? Let’s imagine that you have lost your keys and your car is open, this could seem obvious. However, you should know that if your Peugeot Partner Tepee is newer than the mid 90’s it will be tricky to turn on it without a key because of all the security gadgets present on it. Of course, this should only be done on YOUR car. Here is the technique to adhere to:
- Remove the cover that covers your steering wheel and find among the 3 electric switches the one that concerns your engine/battery/starter (to help you, please bring your user manual).
- Strip, connect them jointly and isolate the battery and ignition wires (be careful not to electrocute yourself during the procedure). You now have electricity as if you had the contact
- At last, strip the starter wire and connect it promptly with the battery wire (do not make extended contact and only 1 or 2 seconds should be enough to start your Peugeot Partner Tepee).
There, you’ve found out all the solutions to start a Peugeot Partner Tepee.
If you need more tutorials on the Peugeot Partner Tepee, go to our Peugeot Partner Tepee category.
