If you’re a bit of a do-it-yourselfer, you’re probably keen to look after most of the service to be done on your Mitsubishi Pajero 3, but some are more challenging than others and need the removal of body parts or elements to access the component you want to work on. We would like to help you in this operation. That’s why in this article we are going to discover how to remove the bumper from a Mitsubishi Pajero 3. This task is not very challenging and you should be able to do it with few equipment. For that, first we will see how to remove the front bumper of your Mitsubishi Pajero 3, then how to remove the rear bumper of this one.

remove-bumper-mitsubishi-pajero-3

How to remove the front bumper from a Mitsubishi Pajero 3

So let’s commence our content page with the front bumper of your Mitsubishi Pajero 3. To remove it, you will just require a set of ratchet wrenches, some screwdrivers and torx bits. Here are the simple steps you will have to adhere to to be able to disassemble the bumper of your Mitsubishi Pajero 3 in good conditions:

  • If you want to be more relaxed, we advise you to lift your Mitsubishi Pajero 3 and to remove the front wheels to have a good access to the whole front bumper.
  • Open the bonnet of your motor vehicle: Would seem obvious, but you will need to have access to the bumper attachment in your engine compartment.
  • Take off the wheel arches: They’re also identified as fenders, but they’ll get in the way and stop you from accessing all the screws on the front bumper of your Mitsubishi Pajero 3. Depending on your automobile features and the year of your model, you will also have the ability to find staples, to do this, you will just have to use a staple extractor or to do it carefully with a big flat screwdriver, and use a lever to open the staple.
  • Then you will have to unscrew the screws that is behind your mudguard and that seals the front bumper of your Mitsubishi Pajero 3 on the sides.
  • Unscrew the screws or remove the clips on the upper part of the bumper in the engine bay.
  • Now it’s time to go underneath your Mitsubishi Pajero 3 to unscrew the bolts that are on the chassis of the automobile, you will find some in the middle of the bumper and on the sides.
  • Make sure to unplug the connection of the plate lighting and the distance control sensor if you have it.
  • Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you perhaps forgot a screw or a clip. Think of using a carpet or other to prevent that it gets scratched by touching the ground.

That’s it, you’ve seen all the steps of how to remove the front bumper from your Mitsubishi Pajero 3, to put it back in place adhere to the steps in the opposite direction.

How to remove the rear bumper from a Mitsubishi Pajero 3

And to finish, regardless if the process is quite similar, we will check out the case of removing the rear bumper from your Mitsubishi Pajero 3. For each step to avoid repeating ourselves we will just give you the broad highlights, refer to part 1 if you have any uncertainties or questions for more information.

  • Start by undertaking the same first step, that is, lift your Mitsubishi Pajero 3 and remove your rear wheels to be able to have an optimal working area to remove the bumper of your Mitsubishi Pajero 3 without trouble
  • Remove the rear wheel arches of your Mitsubishi Pajero 3 to access the side bumper side brackets
  • Open your trunk
  • Take off the side brackets in your wheel arches to make it less complicated to remove the bumper from your Mitsubishi Pajero 3.
  • Remove the lower bindings underneath your Mitsubishi Pajero 3.
  • At the same time, make sure to disconnect the rear license plate light and the reverse radar sensors if you are equipped with them.
  • Unscrew the top brackets from the top of the trunk.
  • Now all you have to do is remove the rear bumper from your Mitsubishi Pajero 3, adhere to the same method as for the front bumper

Here, you have seen through these two parts, how to remove the bumper from a Mitsubishi Pajero 3 whether it is the front one or the rear one the methods are just about the same and it is enough to be careful to make everything go well.

To find more tips on the Mitsubishi Pajero 3, take a look at the Mitsubishi Pajero 3 category.