If you’re a bit of a handy person, you’re quite likely willing to look after almost all of the service to be completed on your Mazda CX 7, but some are more difficult than others and need the removal of body parts or components to access the part you want to focus on. We would like to help you in this task. That’s why in this article we are going to discover how to remove the bumper from a Mazda CX 7. This action is not very difficult and you should have the ability to do it with few equipment. To do so , first we will see how to remove the front bumper of your Mazda CX 7, then how to remove the rear bumper of this one.
How to remove the front bumper from a Mazda CX 7
So let’s commence our content page with the front bumper of your Mazda CX 7. To take it off, you will just need a set of ratchet wrenches, some screwdrivers and torx bits. Here are the steps you will have to adhere to in order to disassemble the bumper of your Mazda CX 7 in good conditions:
- If you want to be more comfy, we encourage you to put your Mazda CX 7 on stands and to remove the front wheels to have a good access to the whole front bumper.
- Open the bonnet of your automobile: Seems obvious, but you will need to have access to the bumper attachment in your engine compartment.
- Take out the wheel arches: They’re also identified as fenders, but they’ll get in the way and stop you from accessing all the screws on the front bumper of your Mazda CX 7. Dependant on your vehicle features and the year of your model, you will also be able to find staples, to do this, you will just have to use a staple extractor or to do it gently with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is at the rear of your mudguard and that seals the front bumper of your Mazda CX 7 on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine bay.
- Now it’s time to go beneath your Mazda CX 7 to unscrew the bolts that are on the chassis of the vehicle, you will find some in the middle of the bumper and on the sides.
- Remember to unplug the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you quite likely forgot a screw or a clip. Think of employing a carpet or other to avoid that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Mazda CX 7, to reassemble it adhere to the steps in the opposite way.
How to remove the rear bumper from a Mazda CX 7
And to finish, even if the operation is quite similar, we will check out the case of removing the rear bumper from your Mazda CX 7. For each stage to avoid repeating ourselves we will just give you the broad outlines, read the part 1 if you have any uncertainties or questions for more details.
- Start by performing the same first stage, that is, lift your Mazda CX 7 and take out your rear wheels in order to have an ideal working area to remove the bumper of your Mazda CX 7 serenely
- Remove the rear wheel arches of your Mazda CX 7 to access the side bumper side brackets
- Open your trunk
- Take out the side brackets in your wheel arches to make it much easier to remove the bumper from your Mazda CX 7.
- Take out the lower bindings below your Mazda CX 7.
- Simultaneously, remember to un plug the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Mazda CX 7, adhere to the same technique as for the front bumper
Here, you have discoverd through these two parts, how to remove the bumper from a Mazda CX 7 whether it is the front one or the rear one the methods are essentially the same and it is enough to be meticulous to make everything go well.
If you wish more guides on the Mazda CX 7, go to our Mazda CX 7 category.
