If you’re a bit of a handy person, you’re most certainly willing to manage the vast majority of the service to be achieved on your Mazda 3, but some are more difficult than others and necessitate the removal of body parts or parts to access the component you want to focus on. We really want to help you in this task. That’s why on this web page we are going to discover how to remove the bumper from a Mazda 3. This task is not very difficult and you should be able to do it with few equipment. To do so , first we will see how to remove the front bumper of your Mazda 3, then how to remove the rear bumper of this one.

remove-bumper-mazda-3

How to remove the front bumper from a Mazda 3

So let’s commence our article with the front bumper of your Mazda 3. To remove it, you will just need a set of ratchet wrenches, some screwdrivers and torx bits. Here are the guidelines you will have to adhere to in order to disassemble the bumper of your Mazda 3 in good conditions:

  • If you want to be more relaxed, we suggest you to put your Mazda 3 on stands and to remove the front wheels to have a perfect access to the whole front bumper.
  • Open the bonnet of your vehicle: Would seem obvious, but you will need to have access to the bumper attachment in your engine compartment.
  • Take out the wheel arches: They’re also referred to as fenders, but they’ll get in the way and prevent you from accessing all the screws on the front bumper of your Mazda 3. Dependant on your vehicle features and the year of your model, you will also have the ability to find staples, to get this done, you will just have to use a staple extractor or to do it gently with a big flat screwdriver, and use a lever to open the staple.
  • Then you will have to unscrew the screws that is at the rear of your mudguard and that seals the front bumper of your Mazda 3 on the sides.
  • Unscrew the screws or remove the clips on the upper part of the bumper in the engine compartment.
  • Now it’s time to go under your Mazda 3 to unscrew the bolts that are on the chassis of the vehicle, you will find some in the middle of the bumper and on the sides.
  • Make sure to disconnect the connection of the plate lighting and the distance control sensor if you have it.
  • Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you most likely forgot a screw or a clip. Think of using a carpet or other to avoid that it gets scratched by touching the ground.

That’s it, you’ve seen all the steps of how to remove the front bumper from your Mazda 3, to put it back in place adhere to the steps in the opposite way.

How to remove the rear bumper from a Mazda 3

And to finish, whether or not the process is quite similar, we will look at the case of removing the rear bumper from your Mazda 3. For each stage to avoid repeating ourselves we will only give you the broad outlines, refer to part 1 if you have any uncertainties or questions for more info.

  • Start by executing the same first stage, that is, lift your Mazda 3 and remove your rear wheels in order to have an ideal working area to remove the bumper of your Mazda 3 serenely
  • Remove the rear wheel arches of your Mazda 3 to access the side bumper side brackets
  • Open your trunk
  • Take out the side brackets in your wheel arches to make it more convenient to remove the bumper from your Mazda 3.
  • Take off the lower bindings below your Mazda 3.
  • Simultaneously, make sure to un plug the rear license plate light and the reverse radar sensors if you are equipped with them.
  • Unscrew the top brackets from the top of the trunk.
  • Now all you have to do is remove the rear bumper from your Mazda 3, adhere to the same process as for the front bumper

Here, you have learned through these two parts, how to remove the bumper from a Mazda 3 whether it is the front one or the rear one the methods are almost the same and it is enough to be meticulous to make everything go well.

Whenever you have any further questions about the Mazda 3, do not hesitate to consult our Mazda 3 category.