If you’re a bit of a handy person, you’re probably willing to look after almost all of the work to be achieved on your Mazda 2, but some are more complicated than others and necessitate the removal of body parts or elements to access the component you want to operate on. We want to help you in this process. That’s why today we are going to see how to remove the bumper from a Mazda 2. This process is not very complicated and you should be able to do it with few tools. To do so , first we will discover how to remove the front bumper of your Mazda 2, then how to remove the rear bumper of this one.
How to remove the front bumper from a Mazda 2
So let’s begin our article content with the front bumper of your Mazda 2. To take it off, you will just require a set of ratchet wrenches, some screwdrivers and torx bits. Here are the steps you will have to adhere to to be able to disassemble the bumper of your Mazda 2 in good conditions:
- If you want to be more comfortable, we recommend you to lift your Mazda 2 and to remove the front wheels to have a good access to the whole front bumper.
- Open the bonnet of your car: Seems obvious, but you will need to have access to the bumper attachment in your engine compartment.
- Remove the wheel arches: They’re also described as fenders, but they’ll get in the way and stop you from accessing all the screws on the front bumper of your Mazda 2. Depending on your automobile features and the year of your model, you will also be able to find staples, to achieve this, you will just have to use a staple extractor or to do it carefully with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is behind your mudguard and that fastens the front bumper of your Mazda 2 on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine compartment.
- Now it’s time to go below your Mazda 2 to unscrew the bolts that are on the chassis of the automobile, you will find some in the middle of the bumper and on the sides.
- Be sure you unplug the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you perhaps forgot a screw or a clip. Think of employing a carpet or other to avoid that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Mazda 2, to put it back in place adhere to the steps in the opposite way.
How to remove the rear bumper from a Mazda 2
And to finish, whether or not the process is quite identical, we will take a look at the case of removing the rear bumper from your Mazda 2. For each step to avoid repeating ourselves we will only give you the broad highlights, read the part 1 if you have any concerns or questions for more details.
- Start by performing the same first step, that is, lift your Mazda 2 and take out your rear wheels to be able to have an ideal working area to remove the bumper of your Mazda 2 without trouble
- Remove the rear wheel arches of your Mazda 2 to access the side bumper side brackets
- Open your trunk
- Remove the side brackets in your wheel arches to make it easier to remove the bumper from your Mazda 2.
- Remove the lower bindings underneath your Mazda 2.
- While doing so, make sure to disconnect the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Mazda 2, adhere to the same operation as for the front bumper
Here, you have discoverd through these two parts, how to remove the bumper from a Mazda 2 whether it is the front one or the rear one the approaches are pretty much the same and it is enough to be careful to make everything go well.
If you wish more guides on the Mazda 2, go to our Mazda 2 category.
