If you’re a bit of a do-it-yourselfer, you’re almost certainly keen to handle the majority of the work to be achieved on your Fiat Panda 3, but some are more complex than others and require the removal of body parts or elements to access the component you want to work on. We want to help you in this task. That’s why on this web page we are going to view how to remove the bumper from a Fiat Panda 3. This procedure is not very complex and you should have the ability to do it with few equipment. For that, first we will discover how to remove the front bumper of your Fiat Panda 3, then how to remove the rear bumper of this one.
How to remove the front bumper from a Fiat Panda 3
So let’s start our article content with the front bumper of your Fiat Panda 3. To take it off, you will just need a set of ratchet wrenches, some screwdrivers and torx bits. Here are the guidelines you will have to stick to to be able to disassemble the bumper of your Fiat Panda 3 in good conditions:
- If you want to be more comfortable, we encourage you to put your Fiat Panda 3 on stands and to remove the front wheels to have a good access to the whole front bumper.
- Open the bonnet of your automobile: Seems evident, but you will need to have access to the bumper attachment in your engine compartment.
- Take away the wheel arches: They’re also referred to as fenders, but they’ll get in the way and prevent you from accessing all the screws on the front bumper of your Fiat Panda 3. Dependant on your car features and the year of your model, you will also be able to find staples, to achieve this, you will just have to use a staple extractor or to do it gently with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is behind your mudguard and that fastens the front bumper of your Fiat Panda 3 on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine bay.
- Now it’s time to go underneath your Fiat Panda 3 to unscrew the bolts that are on the chassis of the car, you will find some in the middle of the bumper and on the sides.
- Make sure unplug the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you quite likely forgot a screw or a clip. Think of using a carpet or other to avoid that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Fiat Panda 3, to reassemble it stick to the steps in the opposite direction.
How to remove the rear bumper from a Fiat Panda 3
And now, even if the procedure is quite similar, we will check out the case of removing the rear bumper from your Fiat Panda 3. For each stage to avoid repeating ourselves we will exclusively give you the broad outlines, refer to part 1 if you have any uncertainties or questions for more details.
- Start by carrying out the same first stage, that is, lift your Fiat Panda 3 and take out your rear wheels to be able to have an optimal working space to remove the bumper of your Fiat Panda 3 serenely
- Remove the rear wheel arches of your Fiat Panda 3 to access the side bumper side brackets
- Open your trunk
- Take away the side brackets in your wheel arches to make it less difficult to remove the bumper from your Fiat Panda 3.
- Take out the lower bindings below your Fiat Panda 3.
- While doing so, be sure you un plug the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Fiat Panda 3, stick to the same process as for the front bumper
Here, you have discoverd through these two parts, how to remove the bumper from a Fiat Panda 3 whether it is the front one or the rear one the methods are more or less the same and it is enough to be careful to make everything go well.
To discover more tips on the Fiat Panda 3, take a look at the Fiat Panda 3 category.
