If you’re a bit of a handy person, you’re most likely wanting to manage most of the work to be done on your Fiat Ducato, but some are more complicated than others and need the removal of body parts or elements to access the part you want to focus on. We want to help you in this process. That’s why in this article we are going to find out how to remove the bumper from a Fiat Ducato. This task is not very complicated and you should be able to do it with few tools. To accomplish this, first we will see how to remove the front bumper of your Fiat Ducato, then how to remove the rear bumper of this one.
How to remove the front bumper from a Fiat Ducato
So let’s start our document with the front bumper of your Fiat Ducato. To remove it, you will just require a set of ratchet wrenches, some screwdrivers and torx bits. Here are the simple steps you will have to stick to to be able to disassemble the bumper of your Fiat Ducato in good conditions:
- If you want to be more relaxed, we recommend you to lift your Fiat Ducato and to remove the front wheels to have a perfect access to the whole front bumper.
- Open the bonnet of your automobile: Would seem evident, but you will need to have access to the bumper attachment in your engine compartment.
- Take away the wheel arches: They’re also described as fenders, but they’ll get in the way and prevent you from accessing all the screws on the front bumper of your Fiat Ducato. According to your car features and the year of your model, you will also have the ability to find staples, to accomplish this, you will just have to use a staple extractor or to do it gently with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is from behind your mudguard and that locks the front bumper of your Fiat Ducato on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine bay.
- Now it’s time to go beneath your Fiat Ducato to unscrew the bolts that are on the chassis of the car, you will find some in the middle of the bumper and on the sides.
- Be sure you disconnect the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you almost certainly forgot a screw or a clip. Think of using a carpet or other to avoid that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Fiat Ducato, to reassemble it stick to the steps in the opposite way.
How to remove the rear bumper from a Fiat Ducato
And to conclude, whether or not the procedure is quite identical, we will check out the case of removing the rear bumper from your Fiat Ducato. For each stage to avoid repeating ourselves we will only give you the broad highlights, read the part 1 if you have any concerns or questions for more info.
- Start with executing the same first stage, that is, lift your Fiat Ducato and take out your rear wheels to be able to have an optimal working area to remove the bumper of your Fiat Ducato without trouble
- Remove the rear wheel arches of your Fiat Ducato to access the side bumper side brackets
- Open your trunk
- Take away the side brackets in your wheel arches to make it much easier to remove the bumper from your Fiat Ducato.
- Take off the lower bindings below your Fiat Ducato.
- While doing so, be sure you un plug the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Fiat Ducato, stick to the same operation as for the front bumper
Here, you have discoverd through these two parts, how to remove the bumper from a Fiat Ducato whether it is the front one or the rear one the ways are essentially the same and it is enough to be careful to make everything go well.
If perhaps you have any additional questions about the Fiat Ducato, do not hesitate to consult our Fiat Ducato category.
