If you’re a bit of a do-it-yourselfer, you’re almost certainly wanting to look after most of the maintenance to be achieved on your Dodge Caliber, but some are more complicated than others and necessitate the removal of body parts or parts to access the component you want to operate on. We want to help you in this task. That’s why in this article we are going to see how to remove the bumper from a Dodge Caliber. This operation is not very complicated and you should be able to do it with few equipment. To accomplish this, first we will see how to remove the front bumper of your Dodge Caliber, then how to remove the rear bumper of this one.
How to remove the front bumper from a Dodge Caliber
So let’s commence our content with the front bumper of your Dodge Caliber. To take it off, you will just require a set of ratchet wrenches, some screwdrivers and torx bits. Here are the simple steps you will have to stick to to be able to disassemble the bumper of your Dodge Caliber in good conditions:
- If you want to be more relaxed, we suggest you to lift your Dodge Caliber and to remove the front wheels to have a good access to the whole front bumper.
- Open the bonnet of your motor vehicle: Would seem obvious, but you will need to have access to the bumper attachment in your engine compartment.
- Take away the wheel arches: They’re also named fenders, but they’ll get in the way and stop you from accessing all the screws on the front bumper of your Dodge Caliber. Depending on your car features and the year of your model, you will also be able to find staples, to get this done, you will just have to use a staple extractor or to do it gently with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is behind your mudguard and that fastens the front bumper of your Dodge Caliber on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine compartment.
- Now it’s time to go underneath your Dodge Caliber to unscrew the bolts that are on the chassis of the car, you will find some in the middle of the bumper and on the sides.
- Make sure to unplug the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you quite likely forgot a screw or a clip. Think of working with a carpet or other to prevent that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Dodge Caliber, to put it back in place stick to the steps in the opposite direction.
How to remove the rear bumper from a Dodge Caliber
And now, even if the procedure is quite similar, we will check out the case of removing the rear bumper from your Dodge Caliber. For each stage to avoid repeating ourselves we will only give you the broad highlights, refer to part 1 if you have any concerns or questions for more details.
- Start with undertaking the same first stage, that is, lift your Dodge Caliber and remove your rear wheels to be able to have an ideal working space to remove the bumper of your Dodge Caliber without trouble
- Remove the rear wheel arches of your Dodge Caliber to access the side bumper side brackets
- Open your trunk
- Take away the side brackets in your wheel arches to make it more convenient to remove the bumper from your Dodge Caliber.
- Take away the lower bindings underneath your Dodge Caliber.
- At the same time, make sure to disconnect the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Dodge Caliber, stick to the same operation as for the front bumper
Here, you have learned through these two parts, how to remove the bumper from a Dodge Caliber whether it is the front one or the rear one the ways are almost the same and it is enough to be careful to make everything go well.
To discover more tips on the Dodge Caliber, take a look at the Dodge Caliber category.
