If you’re a bit of a do-it-yourselfer, you’re quite likely keen to handle most of the work to be carried out on your Chrysler 200, but some are more challenging than others and necessitate the removal of body parts or elements to access the part you want to operate on. We want to help you in this process. That’s why on this web page we are going to view how to remove the bumper from a Chrysler 200. This action is not very challenging and you should be able to do it with few equipment. For that, first we will discover how to remove the front bumper of your Chrysler 200, then how to remove the rear bumper of this one.
How to remove the front bumper from a Chrysler 200
So let’s begin our article content with the front bumper of your Chrysler 200. To remove it, you will just need a set of ratchet wrenches, some screwdrivers and torx bits. Here are the steps you will have to follow to be able to disassemble the bumper of your Chrysler 200 in good conditions:
- If you want to be more relaxed, we encourage you to lift your Chrysler 200 and to remove the front wheels to have a best access to the whole front bumper.
- Open the bonnet of your vehicle: Would seem obvious, but you will need to have access to the bumper attachment in your engine compartment.
- Take off the wheel arches: They’re also referred to as fenders, but they’ll get in the way and stop you from accessing all the screws on the front bumper of your Chrysler 200. Depending on your motor vehicle features and the year of your model, you will also be able to find staples, to achieve this, you will just have to use a staple extractor or to do it delicately with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is from behind your mudguard and that seals the front bumper of your Chrysler 200 on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine bay.
- Now it’s time to go beneath your Chrysler 200 to unscrew the bolts that are on the chassis of the motor vehicle, you will find some in the middle of the bumper and on the sides.
- Remember to disconnect the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you almost certainly forgot a screw or a clip. Think of working with a carpet or other to prevent that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Chrysler 200, to put it back in place follow the steps in the opposite way.
How to remove the rear bumper from a Chrysler 200
And to finish, even if the process is quite equivalent, we will take a look at the case of removing the rear bumper from your Chrysler 200. For each stage to avoid repeating ourselves we will just give you the broad highlights, refer to part 1 if you have any uncertainties or questions for more information.
- Start with performing the same first stage, that is, lift your Chrysler 200 and take off your rear wheels to be able to have an ideal working space to remove the bumper of your Chrysler 200 without trouble
- Remove the rear wheel arches of your Chrysler 200 to access the side bumper side brackets
- Open your trunk
- Take off the side brackets in your wheel arches to make it less complicated to remove the bumper from your Chrysler 200.
- Take out the lower bindings below your Chrysler 200.
- At the same time, make sure un plug the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Chrysler 200, follow the same procedure as for the front bumper
Here, you have discoverd through these two parts, how to remove the bumper from a Chrysler 200 whether it is the front one or the rear one the solutions are more or less the same and it is enough to be meticulous to make everything go well.
If you need more tutorials on the Chrysler 200, go to our Chrysler 200 category.
