If you’re a bit of a do-it-yourselfer, you’re probably wanting to take care of the vast majority of the work to be completed on your Audi Q8, but some are more complex than others and need the removal of body parts or components to access the part you want to focus on. We would like to help you in this task. That’s why on this web page we are going to find out how to remove the bumper from a Audi Q8. This task is not very complex and you should have the ability to do it with few equipment. To do so , first we will discover how to remove the front bumper of your Audi Q8, then how to remove the rear bumper of this one.
How to remove the front bumper from a Audi Q8
So let’s begin our document with the front bumper of your Audi Q8. To take it off, you will just need a set of ratchet wrenches, some screwdrivers and torx bits. Here are the steps you will have to adhere to to be able to disassemble the bumper of your Audi Q8 in good conditions:
- If you want to be more comfortable, we encourage you to lift your Audi Q8 and to remove the front wheels to have a good access to the whole front bumper.
- Open the bonnet of your automobile: Would seem obvious, but you will need to have access to the bumper attachment in your engine compartment.
- Take away the wheel arches: They’re also known as fenders, but they’ll get in the way and prevent you from accessing all the screws on the front bumper of your Audi Q8. Depending on your motor vehicle features and the year of your model, you will also be able to find staples, to do this, you will just have to use a staple extractor or to do it delicately with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is from behind your mudguard and that locks the front bumper of your Audi Q8 on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine bay.
- Now it’s time to go beneath your Audi Q8 to unscrew the bolts that are on the chassis of the motor vehicle, you will find some in the middle of the bumper and on the sides.
- Make sure unplug the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you quite likely forgot a screw or a clip. Think of employing a carpet or other to prevent that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Audi Q8, to put it back in place adhere to the steps in the opposite direction.
How to remove the rear bumper from a Audi Q8
And to conclude, whether or not the procedure is quite similar, we will look at the case of removing the rear bumper from your Audi Q8. For each step to avoid repeating ourselves we will exclusively give you the broad highlights, read the part 1 if you have any uncertainties or questions for more info.
- Start with undertaking the same first step, that is, lift your Audi Q8 and take out your rear wheels to be able to have an ideal working area to remove the bumper of your Audi Q8 without trouble
- Remove the rear wheel arches of your Audi Q8 to access the side bumper side brackets
- Open your trunk
- Take away the side brackets in your wheel arches to make it less difficult to remove the bumper from your Audi Q8.
- Take out the lower bindings below your Audi Q8.
- At the same time, make sure to un plug the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Audi Q8, adhere to the same operation as for the front bumper
Here, you have discoverd through these two parts, how to remove the bumper from a Audi Q8 whether it is the front one or the rear one the solutions are essentially the same and it is enough to be careful to make everything go well.
If you want more guides on the Audi Q8, go to our Audi Q8 category.
