If you’re a bit of a handy person, you’re most certainly keen to look after the vast majority of the service to be carried out on your Audi A6, but some are more challenging than others and require the removal of body parts or parts to access the part you want to work on. We would really like to help you in this task. That’s why on this web page we are going to view how to remove the bumper from a Audi A6. This process is not very challenging and you should have the ability to do it with few tools. To accomplish this, first we will see how to remove the front bumper of your Audi A6, then how to remove the rear bumper of this one.
How to remove the front bumper from a Audi A6
So let’s commence our content with the front bumper of your Audi A6. To take it off, you will just require a set of ratchet wrenches, some screwdrivers and torx bits. Here are the steps you will have to adhere to to be able to disassemble the bumper of your Audi A6 in good conditions:
- If you want to be more comfortable, we recommend you to lift your Audi A6 and to remove the front wheels to have a good access to the whole front bumper.
- Open the bonnet of your car: Would seem obvious, but you will need to have access to the bumper attachment in your engine compartment.
- Take out the wheel arches: They’re also described as fenders, but they’ll get in the way and stop you from accessing all the screws on the front bumper of your Audi A6. According to your automobile features and the year of your model, you will also be able to find staples, to achieve this, you will just have to use a staple extractor or to do it delicately with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is at the rear of your mudguard and that locks the front bumper of your Audi A6 on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine bay.
- Now it’s time to go beneath your Audi A6 to unscrew the bolts that are on the chassis of the automobile, you will find some in the middle of the bumper and on the sides.
- Make sure to unplug the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you quite likely forgot a screw or a clip. Think of using a carpet or other to avoid that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Audi A6, to reassemble it adhere to the steps in the opposite direction.
How to remove the rear bumper from a Audi A6
And to finish, regardless if the operation is quite equivalent, we will look at the case of removing the rear bumper from your Audi A6. For each stage to avoid repeating ourselves we will exclusively give you the broad outlines, read the part 1 if you have any concerns or questions for more information.
- Start by carrying out the same first stage, that is, lift your Audi A6 and take out your rear wheels to be able to have an optimal working area to remove the bumper of your Audi A6 serenely
- Remove the rear wheel arches of your Audi A6 to access the side bumper side brackets
- Open your trunk
- Take out the side brackets in your wheel arches to make it less difficult to remove the bumper from your Audi A6.
- Take out the lower bindings below your Audi A6.
- At the same time, remember to un plug the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Audi A6, adhere to the same procedure as for the front bumper
Here, you have learned through these two parts, how to remove the bumper from a Audi A6 whether it is the front one or the rear one the ways are pretty much the same and it is enough to be careful to make everything go well.
In the event that you have any further questions about the Audi A6, do not hesitate to consult our Audi A6 category.
