If you’re a bit of a do-it-yourselfer, you’re quite likely wanting to manage the majority of the work to be achieved on your Audi A3, but some are more complex than others and require the removal of body parts or components to access the part you want to focus on. We would like to help you in this task. That’s why in this article we are going to view how to remove the bumper from a Audi A3. This task is not very complex and you should be able to do it with few tools. To do so , first we will discover how to remove the front bumper of your Audi A3, then how to remove the rear bumper of this one.
How to remove the front bumper from a Audi A3
So let’s begin our content page with the front bumper of your Audi A3. To take it off, you will just require a set of ratchet wrenches, some screwdrivers and torx bits. Here are the simple steps you will have to follow to be able to disassemble the bumper of your Audi A3 in good conditions:
- If you want to be more comfortable, we encourage you to lift your Audi A3 and to remove the front wheels to have a best access to the whole front bumper.
- Open the bonnet of your motor vehicle: Seems obvious, but you will need to have access to the bumper attachment in your engine compartment.
- Remove the wheel arches: They’re also known as fenders, but they’ll get in the way and stop you from accessing all the screws on the front bumper of your Audi A3. Depending on your car features and the year of your model, you will also be able to find staples, to accomplish this, you will just have to use a staple extractor or to do it gently with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is from behind your mudguard and that fastens the front bumper of your Audi A3 on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine bay.
- Now it’s time to go underneath your Audi A3 to unscrew the bolts that are on the chassis of the car, you will find some in the middle of the bumper and on the sides.
- Make sure unplug the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you most likely forgot a screw or a clip. Think of employing a carpet or other to prevent that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Audi A3, to reassemble it follow the steps in the opposite direction.
How to remove the rear bumper from a Audi A3
And to finish, regardless if the operation is quite equivalent, we will take a look at the case of removing the rear bumper from your Audi A3. For each step to avoid repeating ourselves we will just give you the broad outlines, refer to part 1 if you have any uncertainties or questions for more info.
- Start with executing the same first step, that is, lift your Audi A3 and take off your rear wheels to be able to have an optimal working area to remove the bumper of your Audi A3 without trouble
- Remove the rear wheel arches of your Audi A3 to access the side bumper side brackets
- Open your trunk
- Remove the side brackets in your wheel arches to make it less difficult to remove the bumper from your Audi A3.
- Remove the lower bindings below your Audi A3.
- Simultaneously, make sure disconnect the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Audi A3, follow the same operation as for the front bumper
Here, you have discoverd through these two parts, how to remove the bumper from a Audi A3 whether it is the front one or the rear one the ways are more or less the same and it is enough to be meticulous to make everything go well.
To find more tips on the Audi A3, take a look at the Audi A3 category.
