If you’re a bit of a handy person, you’re most likely keen to take care of most of the service to be achieved on your Acura MDX, but some are more challenging than others and need the removal of body parts or parts to access the part you want to operate on. We would really like to help you in this process. That’s why in this article we are going to find out how to remove the bumper from a Acura MDX. This process is not very challenging and you should be able to do it with few tools. To do so , first we will discover how to remove the front bumper of your Acura MDX, then how to remove the rear bumper of this one.
How to remove the front bumper from a Acura MDX
So let’s start our article content with the front bumper of your Acura MDX. To take it off, you will just need a set of ratchet wrenches, some screwdrivers and torx bits. Here are the simple steps you will have to stick to in order to disassemble the bumper of your Acura MDX in good conditions:
- If you want to be more comfortable, we suggest you to lift your Acura MDX and to remove the front wheels to have a best access to the whole front bumper.
- Open the bonnet of your automobile: Would seem evident, but you will need to have access to the bumper attachment in your engine compartment.
- Take off the wheel arches: They’re also known as fenders, but they’ll get in the way and prevent you from accessing all the screws on the front bumper of your Acura MDX. Dependant on your automobile features and the year of your model, you will also have the ability to find staples, to accomplish this, you will just have to use a staple extractor or to do it delicately with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is in back of your mudguard and that seals the front bumper of your Acura MDX on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine compartment.
- Now it’s time to go beneath your Acura MDX to unscrew the bolts that are on the chassis of the automobile, you will find some in the middle of the bumper and on the sides.
- Make sure to disconnect the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you perhaps forgot a screw or a clip. Think of working with a carpet or other to avoid that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Acura MDX, to put it back in place stick to the steps in the opposite way.
How to remove the rear bumper from a Acura MDX
And to conclude, even if the operation is quite identical, we will check out the case of removing the rear bumper from your Acura MDX. For each stage to avoid repeating ourselves we will just give you the broad outlines, read the part 1 if you have any concerns or questions for more information.
- Start with executing the same first stage, that is, lift your Acura MDX and take off your rear wheels in order to have an ideal working space to remove the bumper of your Acura MDX serenely
- Remove the rear wheel arches of your Acura MDX to access the side bumper side brackets
- Open your trunk
- Take off the side brackets in your wheel arches to make it less complicated to remove the bumper from your Acura MDX.
- Remove the lower bindings underneath your Acura MDX.
- While doing so, make sure disconnect the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Acura MDX, stick to the same procedure as for the front bumper
Here, you have discoverd through these two parts, how to remove the bumper from a Acura MDX whether it is the front one or the rear one the ways are more or less the same and it is enough to be careful to make everything go well.
To discover more tips on the Acura MDX, take a look at the Acura MDX category.
