It doesn’t matter if it’s for your own safety, for roadworthiness testing or to avoid a fine, being certain your headlamp bulbs are constantly functional is very important. In fact, bulbs are wearing parts that will inevitably burn out after some time and therefore need to be replaced. You’re almost certainly here because one of your position lamp is burnt out and you’re wondering how to change the bulb of my Toyota Sequoia parking light, we’ve posted this content to help you do this operation without any help and not need to go to your repair shop. In a first step, we will look at changing the front daytime running light bulb of your car and in a second art, how to change the rear daytime running light.

change-parking-light-toyota-sequoia

How to change the front parking light bulb of my Toyota Sequoia?

We will commence this article with swapping the front daytime running light bulb of your Toyota Sequoia, take note that depending on the year and finish of your car it may not be quite the same methodology to use. In fact, even if the position of your bulb is not going to change, the access may be more or less difficult based on the features of your car.

First methodology, we will execute the bulb change of your daytime running light without removing the headlight of your Toyota Sequoia. Although this process is the simplest, it is not assured that you will be able to accomplish it on your motor vehicle without encumbrance. In fact, depending on the versions and the year, on some versions there will not be enough space for you to change the bulb that way. Here are the two distinct solutions to change the bulb of the front parking light of your Toyota Sequoia:.

  • Going through the bonnet of your car: First methodology, you will simply go through the bonnet of your motor vehicle to direct access your headlight unit. This is the most wise approach but it is not always easy to realise, sometimes because of secondary parts that will obstruct your access. To perform this, here are the simple steps to carry out. First, with the engine off, disconnect the terminals of your battery to avoid any short circuit or risk of electrocution. Now that this step has been completed, you will need to access the back of your headlight unit to change the daytime running light bulb on your Toyota Sequoia. You may need to take out the battery for easier access. In such a case, you will need to open the bulb protection cap on your headlight (¼ in most cases does the job), then you will need to take out the bulb socket from its area. To perform this, pull delicately on the socket and not on the wires (you risk damaging them), finally when the socket is out, you can change your parking lamps bulb, being very careful not to damage the wires and use a cloth to avoid dirtying your new bulb. Once accomplished, reassemble the system, reconnect your battery and carry out a check test before taking to the road.
  • By removing the crosshair grill and the headlight:
  • Second alternative, you can remove the headlight of your Toyota Sequoia in cases where the access through the engine block seems too obstructed. To do this, you just have to open your bonnet, take out the front grill held by only a few torx screws, then take out the headlight in question. Once these actions are finished you will only have to follow the same methodology as on the previous part to change the front daytime running light bulb of your Toyota Sequoia

.

How to change the rear parking light bulb on your Toyota Sequoia

Finally, if you want to swap the rear parking light bulb of your Toyota Sequoia the approach is much easier, here are the different simple steps to follow to allow you to swap this bulb:

  • Disconnect your battery
  • Get the floorboards out of the trunk.
  • Unscrew the back cover of the headlight unit from your car.
  • After locating the rear position lamps bulb on your car, remove the burnt-out bulb.
  • Insert your new parking light bulb into the headlamp assembly on your car
  • Reassemble the whole thing.

Examine that your parking lights are operating properly again before you set off again and you’re done. If you want to change the fog light bulb on your Toyota Sequoia, please browse our dedicated content page to learn how to do it.

Whenever you have any further questions about the Toyota Sequoia, do not hesitate to consult our Toyota Sequoia category.