Regardless it’s for your own personal security, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are in every case functional is really important. In reality, bulbs are wearing auto parts that will surely burn out over the years and as a result need to be replaced. You’re most certainly here because one of your parking lights is burnt out and you’re wondering how to change your Volkswagen Polo’s license plate bulb, we’ve created this article content to help you do it without any help and not have to go to your motor mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Volkswagen Polo.


How to swap the license plate bulb on your Volkswagen Polo throughout the outside

This method is the most simple of the two, in truth, for this one you will only need to remove the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will spend a moment on in the second part of this content to describe the method.
So let’s start with swapping the number plate bulb by going through the outside of your Volkswagen Polo. Regardless it’s the front or the back of your motor vehicle the technique will be identical.
Here are a few simple guidelines to follow to execute this service:

  • With the engine turned off, unplug the battery terminals from your car
  • Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this purpose (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Volkswagen Polo
  • .

  • Use your screwdriver or knife to remove the bulb from its spot, in the event that you are worried of damaging a thing, you can as well do it with your fingers.
  • Finally, put the new license plate light bulb
  • Last step, before reassembling, reconnect your battery and check the light to confirm the successfulness of the task.

How to change the number plate bulb on your Volkswagen Polo without outside access

Second part of our article, replace this license plate bulb on your Volkswagen Polo without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).

How to swap the front license plate bulb on my Volkswagen Polo

To swap the one on the front plate, nothing could be less hard, you will have to put yourself under the motor vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to exert too much pressure or you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and swap it with the new , then check and reassemble the whole thing.

How to swap the rear license plate bulb on my Volkswagen Polo

Finally last possibility, you must swap the bulb on the backplate of your Volkswagen Polo, but you are not able to open the cover from the outside of your motor vehicle. In such a case, here is the process to execute this operation:

  • Unplug the battery from your Volkswagen Polo
  • Identify the location of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
  • Once found, before removing the bulb holders, unplug the holders for easier access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Volkswagen Polo, check it and reassemble it, paying attention to the clips on the trunk liner

There you have it, you have discovered the main methods for swapping license plate bulbs on your car, be aware that on some models the method may be a bit different but you should be able to do it following the outline of this document. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Volkswagen Polo. If you desire to change other bulbs like the position light bulbs on your Volkswagen Polo or the low beam bulbs on Volkswagen Polo, don’t hesitate to read our articles which demonstrate you the process to follow.

If you want more tutorials on the Volkswagen Polo, go to our Volkswagen Polo category.