It doesn’t matter if it’s for your own personal safety, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are constantly effective is really important. In reality, bulbs are wearing parts that will inevitably burn out after some time and therefore need to be replaced. You’re probably in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Volkswagen Polo 6’s license plate bulb, we’ve created this document to help you do it without any help and not have to go to your mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Volkswagen Polo 6.
How to replace the license plate bulb on your Volkswagen Polo 6 through the outside
This approach is the simplest of the two, in truth, for this one you will simply require to take away the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will take some time on in the second section of this content page to describe the way.
So let’s begin with replacing the number plate bulb by going through the outside of your Volkswagen Polo 6. It doesn’t matter if it’s the front or the back of your car the operation will be the same.
Here are a few simple guidelines to stick to to carry out this service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Volkswagen Polo 6
- Use your screwdriver or knife to remove the bulb from its place, in the event that you are worried of breaking anything, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to confirm the achievement of the operation.
.
How to change the number plate bulb on your Volkswagen Polo 6 without outside access
Second section of our content page, swap this license plate bulb on your Volkswagen Polo 6 without external access. Generally you will be able to access it, but some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Volkswagen Polo 6
To replace the one on the front plate, nothing could be less difficult, you will have to put yourself under the car (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Take out the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to apply too much pressure or you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.
How to replace the rear license plate bulb on my Volkswagen Polo 6
Finally last solution, you must replace the bulb on the backplate of your Volkswagen Polo 6, but you are not able to open the cover from the outside of your car. In this case, here is the method to perform this task:
- Unplug the battery from your Volkswagen Polo 6
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Volkswagen Polo 6, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main approaches for replacing license plate bulbs on your car, bear in mind that on some models the methodology may be a bit different but you should be able to realize it following the explanation of this article content. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Volkswagen Polo 6. If you desire to change other bulbs like the position light bulbs on your Volkswagen Polo 6 or the low beam bulbs on Volkswagen Polo 6, don’t hesitate to browse our content articles which describe you the operation to follow.
To get more tips on the Volkswagen Polo 6, take a look at the Volkswagen Polo 6 category.
