Regardless it’s for your personal security, for roadworthiness tests or to avoid a fine, ensuring your headlamp bulbs are always working is necessary. In reality, bulbs are wearing units that will undoubtedly burn out with time and therefore need to be swapped out. You’re likely here because one of your parking lights is burnt out and you’re wanting to know how to change your Volkswagen Polo 3’s license plate bulb, we’ve written this article to help you do it on your own and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Volkswagen Polo 3.

change-license-plate-bulb-volkswagen-polo-3

How to replace the license plate bulb on your Volkswagen Polo 3 coming from the outside

This method is the fastest of the two, in fact, for this one you will simply require to take away the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second part of this document to clarify the method.
So let’s begin with swapping the number plate bulb by going through the outside of your Volkswagen Polo 3. Regardless it’s the front or the back of your motor vehicle the procedure will be similar.
Here are a few simple steps to stick to to conduct this routine service:

  • With the engine turned off, disconnect the battery terminals from your car
  • Face your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this goal (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Volkswagen Polo 3
  • .

  • Use your screwdriver or knife to remove the bulb from its location, in the event that you are scared of destroying something, you can also do it with your fingers.
  • Finally, put the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and verify the light to confirm the success of the process.

How to replace the number plate bulb on your Volkswagen Polo 3 without outside access

Second part of our content, replace this license plate bulb on your Volkswagen Polo 3 without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).

How to replace the front license plate bulb on my Volkswagen Polo 3

To replace the one on the front plate, nothing could be much easier, you will have to put yourself under the motor vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to put in too much pressure otherwise you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.

How to replace the rear license plate bulb on my Volkswagen Polo 3

Finally last solution, you must replace the bulb on the backplate of your Volkswagen Polo 3, but you cannot open the cover from the outside of your motor vehicle. In such a case, here is the method to operate this operation:

  • Unplug the battery from your Volkswagen Polo 3
  • Locate the spot of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
  • Once located, before removing the bulb holders, disconnect the holders for easier access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Volkswagen Polo 3, verify it and reassemble it, paying attention to the clips on the trunk liner

.
There you have it, you have found out the main methods for swapping license plate bulbs on your car, take notice that on some models the method may be a bit different but you should be able to realize it following the explanation of this document. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Volkswagen Polo 3. If you desire to change other bulbs like the position light bulbs on your Volkswagen Polo 3 or the low beam bulbs on Volkswagen Polo 3, don’t hesitate to consult our articles which describe you the operation to follow.

To get more tips on the Volkswagen Polo 3, take a look at the Volkswagen Polo 3 category.