Regardless whether it’s for your own safety, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are all the time functioning is really important. In fact, bulbs are wearing auto parts that will predictably burn out after a while and therefore need to be replaced. You’re likely in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Volkswagen Crafter’s license plate bulb, we’ve made this document to help you do it on your own and not have to go to your mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Volkswagen Crafter.
How to swap the license plate bulb on your Volkswagen Crafter throughout the outside
This option is the easiest of the two, in fact, for this one you will simply require to take away the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will take some time on in the second section of this content to teach you the approach.
So let’s start with changing the number plate bulb by going through the outside of your Volkswagen Crafter. Regardless whether it’s the front or the back of your automobile the procedure will be the same.
Here are a few simple steps to stick to to execute this routine service:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Volkswagen Crafter
- Use your screwdriver or knife to remove the bulb from its spot, in the event that you are scared of damaging a thing, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to validate the successfulness of the procedure.
.
How to change the number plate bulb on your Volkswagen Crafter without outside access
Second section of our article, swap this license plate bulb on your Volkswagen Crafter without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Volkswagen Crafter
To swap the one on the front plate, nothing could be less difficult, you will have to position yourself under the automobile (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to exert too much force or you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.
How to swap the rear license plate bulb on my Volkswagen Crafter
Finally last possibility, you must swap the bulb on the backplate of your Volkswagen Crafter, but you cannot open the cover from the outside of your automobile. In this instance, here is the technique to carry out this operation:
- Disconnect the battery from your Volkswagen Crafter
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Volkswagen Crafter, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main techniques for changing license plate bulbs on your car, take note that on some models the methodology may be a bit different but you should be able to accomplish it following the explanation of this content. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Volkswagen Crafter. If you need to change other bulbs like the position light bulbs on your Volkswagen Crafter or the low beam bulbs on Volkswagen Crafter, don’t hesitate to consult our articles which explain you the process to follow.
If you have any further questions about the Volkswagen Crafter, do not hesitate to consult our Volkswagen Crafter category.
