Regardless it’s for your own personal safety, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are constantly effective is extremely important. Indeed, bulbs are wearing units that will surely burn out after some time and as a consequence need to be swapped out. You’re most certainly here because one of your parking lights is burnt out and you’re wanting to know how to change your Volkswagen Crafter 2’s license plate bulb, we’ve written and published this article content to help you do it all on your own and not have to go to your mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Volkswagen Crafter 2.
How to swap the license plate bulb on your Volkswagen Crafter 2 through the outside
This method is the most simple of the two, actually, for this one you will just have to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second section of this content to describe the approach.
So let’s start with replacing the number plate bulb by going through the outside of your Volkswagen Crafter 2. Regardless it’s the front or the back of your vehicle the method will be identical.
Here are a few simple actions to stick to to conduct this service:
- With the engine off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Volkswagen Crafter 2
- Use your screwdriver or knife to eject the bulb from its spot, in the event that you are worried of damaging something, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to validate the success of the operation.
.
How to change the number plate bulb on your Volkswagen Crafter 2 without outside access
Second section of our item, replace this license plate bulb on your Volkswagen Crafter 2 without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Volkswagen Crafter 2
To swap the one on the front plate, nothing could be less complicated, you will have to put yourself under the vehicle (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both simultaneously, then now that you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to exert too much pressure otherwise you will break the plastic cover), and you will only have to take out the burnt-out license plate bulb and replace it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my Volkswagen Crafter 2
Finally last option, you must swap the bulb on the backplate of your Volkswagen Crafter 2, but you cannot open the cover from the outside of your vehicle. In this instance, here is the tactic to do this operation:
- Disconnect the battery from your Volkswagen Crafter 2
- Locate the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Volkswagen Crafter 2, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main tactics for replacing license plate bulbs on your car, take notice that on some models the technique may be a bit different but you should be able to do it following the explanation of this content. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Volkswagen Crafter 2. If you wish to change other bulbs like the position light bulbs on your Volkswagen Crafter 2 or the low beam bulbs on Volkswagen Crafter 2, don’t be reluctant to read our articles which describe you the procedure to follow.
If you wish more tutorials on the Volkswagen Crafter 2, go to our Volkswagen Crafter 2 category.
