It doesn’t matter if it’s for your personal safety, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are in every case functional is extremely important. In reality, bulbs are wearing units that will obviously burn out over the years and therefore need to be replaced. You’re almost certainly on this site because one of your parking lights is burnt out and you’re questioning how to change your Toyota Yaris 3’s license plate bulb, we’ve written this article to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Toyota Yaris 3.
How to swap the license plate bulb on your Toyota Yaris 3 through the outside
This technique is the quickest of the two, in reality, for this one you will just require to remove the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will spend a moment on in the second part of this article to demonstrate the way.
So let’s begin with replacing the number plate bulb by going through the outside of your Toyota Yaris 3. It doesn’t matter if it’s the front or the back of your automobile the procedure will be similar.
Here are a few simple steps to follow to perform this maintenance tasks:
- With the engine turned off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this purpose (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Yaris 3
- Use your screwdriver or knife to remove the bulb from its placement, in the event you are scared of destroying anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the achievement of the operation.
.
How to change the number plate bulb on your Toyota Yaris 3 without outside access
Second part of our article, swap this license plate bulb on your Toyota Yaris 3 without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Toyota Yaris 3
To swap the one on the front plate, nothing could be less hard, you will have to position yourself under the automobile (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually kept by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to apply too much force otherwise you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to swap the rear license plate bulb on my Toyota Yaris 3
Finally last solution, you must swap the bulb on the backplate of your Toyota Yaris 3, but you simply cannot open the cover from the outside of your automobile. In this instance, here is the process to carry out this task:
- Unplug the battery from your Toyota Yaris 3
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Toyota Yaris 3, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main ways for replacing license plate bulbs on your car, take note that on some models the method may be a bit different but you should be able to realize it following the explanation of this article content. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Toyota Yaris 3. If you want to change other bulbs like the position light bulbs on your Toyota Yaris 3 or the low beam bulbs on Toyota Yaris 3, don’t be reluctant to browse our content articles which describe you the process to follow.
Whenever you have any further questions about the Toyota Yaris 3, do not hesitate to consult our Toyota Yaris 3 category.
