Whether it’s for your own personal security, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are constantly working is really important. In reality, bulbs are wearing parts that will inevitably burn out after awhile and as a consequence need to be replaced. You’re quite likely on this site because one of your parking lights is burnt out and you’re questioning how to change your Toyota Tacoma’s license plate bulb, we’ve made this content to help you do it without any help and not have to go to your auto mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Toyota Tacoma.
How to change the license plate bulb on your Toyota Tacoma through the outside
This technique is the fastest of the two, in fact, for this one you will simply have to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will take a moment on in the second section of this article content to describe the method.
So let’s start with swapping the number plate bulb by going through the outside of your Toyota Tacoma. Whether it’s the front or the back of your vehicle the method will be similar.
Here are a few simple actions to stick to to perform this maintenance tasks:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Tacoma
- Use your screwdriver or knife to eject the bulb from its place, if you are scared of damaging anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to confirm the success of the operation.
.
How to change the number plate bulb on your Toyota Tacoma without outside access
Second section of our document, replace this license plate bulb on your Toyota Tacoma without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Toyota Tacoma
To change the one on the front plate, nothing could be easier, you will have to position yourself under the vehicle (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both simultaneously, then now that you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to apply too much force or you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to change the rear license plate bulb on my Toyota Tacoma
Finally last possibility, you must change the bulb on the backplate of your Toyota Tacoma, but you cannot open the cover from the outside of your vehicle. In this instance, here is the solution to execute this task:
- Unplug the battery from your Toyota Tacoma
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Toyota Tacoma, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main ways for swapping license plate bulbs on your car, take note that on some models the technique may be a bit different but you should be able to realize it following the explanation of this content. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Toyota Tacoma. If you need to change other bulbs like the position light bulbs on your Toyota Tacoma or the low beam bulbs on Toyota Tacoma, don’t be reluctant to browse our content articles which demonstrate you the operation to follow.
To find more tips on the Toyota Tacoma, take a look at the Toyota Tacoma category.
