It doesn’t matter if it’s for your personal safety, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are in every case functional is extremely important. In fact, bulbs are wearing parts that will undoubtedly burn out over the years and as a result need to be swapped out. You’re quite likely in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Toyota Sequoia’s license plate bulb, we’ve written and published this content page to help you do it by yourself and not have to go to your auto technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Toyota Sequoia.
How to change the license plate bulb on your Toyota Sequoia coming from the outside
This method is the simplest of the two, in fact, for this one you will simply need to remove the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate a moment on in the second part of this content to teach you the way.
So let’s start with changing the number plate bulb by going through the outside of your Toyota Sequoia. It doesn’t matter if it’s the front or the back of your motor vehicle the technique will be similar.
Here are a few simple steps to stick to to carry out this maintenance tasks:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Sequoia
- Use your screwdriver or knife to eject the bulb from its placement, if you are scared of breaking anything, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to validate the achievement of the task.
.
How to change the number plate bulb on your Toyota Sequoia without outside access
Second part of our document, replace this license plate bulb on your Toyota Sequoia without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Toyota Sequoia
To change the one on the front plate, nothing could be less complicated, you will have to put yourself under the motor vehicle (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to put in too much pressure otherwise you will break the plastic cover), and you will just have to remove the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my Toyota Sequoia
Finally last possibility, you must change the bulb on the backplate of your Toyota Sequoia, but you cannot open the cover from the outside of your motor vehicle. In such a case, here is the method to perform this task:
- Unplug the battery from your Toyota Sequoia
- Locate the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Toyota Sequoia, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main solutions for changing license plate bulbs on your car, remember that on some models the technique may be a bit different but you should be able to realize it following the explanation of this article. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Toyota Sequoia. If you want to change other bulbs like the position light bulbs on your Toyota Sequoia or the low beam bulbs on Toyota Sequoia, don’t hesitate to browse our articles which demonstrate you the procedure to follow.
To discover more tips on the Toyota Sequoia, take a look at the Toyota Sequoia category.
