Regardless it’s for your specific safety, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are always effective is extremely important. Indeed, bulbs are wearing units that will undoubtedly burn out over the years and as a result need to be swapped out. You’re likely here because one of your parking lights is burnt out and you’re struggling with how to change your Toyota Scion FR S’s license plate bulb, we’ve written this document to help you do it by yourself and not have to go to your mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Toyota Scion FR S.
How to swap the license plate bulb on your Toyota Scion FR S coming from the outside
This solution is the quickest of the two, in truth, for this one you will just have to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will take some time on in the second section of this article to show you the way.
So let’s begin with replacing the number plate bulb by going through the outside of your Toyota Scion FR S. Regardless it’s the front or the back of your automobile the method will be similar.
Here are a few simple steps to follow to execute this maintenance tasks:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this purpose (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Scion FR S
- Use your screwdriver or knife to eject the bulb from its spot, in the event you are scared of destroying anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to confirm the successfulness of the procedure.
.
How to change the number plate bulb on your Toyota Scion FR S without outside access
Second section of our document, change this license plate bulb on your Toyota Scion FR S without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Toyota Scion FR S
To swap the one on the front plate, nothing could be simpler, you will have to position yourself under the automobile (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to exert too much pressure otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my Toyota Scion FR S
Finally last solution, you must swap the bulb on the backplate of your Toyota Scion FR S, but you cannot really open the cover from the outside of your automobile. In such a case, here is the method to perform this task:
- Unplug the battery from your Toyota Scion FR S
- Locate the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Toyota Scion FR S, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main tactics for replacing license plate bulbs on your car, remember that on some models the technique may be a bit different but you should be able to accomplish it following the explanation of this content. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Toyota Scion FR S. If you wish to change other bulbs like the position light bulbs on your Toyota Scion FR S or the low beam bulbs on Toyota Scion FR S, don’t hesitate to read our content articles which explain you the process to follow.
If you need more guides on the Toyota Scion FR S, go to our Toyota Scion FR S category.
