It doesn’t matter if it’s for your specific security, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are constantly functioning is very important. In fact, bulbs are wearing parts that will obviously burn out as time passes and consequently need to be replaced. You’re most likely on this site because one of your parking lights is burnt out and you’re wanting to know how to change your Toyota Matrix’s license plate bulb, we’ve made this content page to help you do it without any help and not have to go to your motor mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Toyota Matrix.
How to swap the license plate bulb on your Toyota Matrix through the outside
This option is the quickest of the two, in reality, for this one you will simply have to take off the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will take a moment on in the second section of this document to demonstrate the approach.
So let’s begin with changing the number plate bulb by going through the outside of your Toyota Matrix. It doesn’t matter if it’s the front or the back of your automobile the process will be identical.
Here are a few simple guidelines to follow to carry out this routine service:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this goal (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Matrix
- Use your screwdriver or knife to remove the bulb from its placement, in the event that you are scared of damaging a thing, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the achievement of the operation.
.
How to replace the number plate bulb on your Toyota Matrix without outside access
Second section of our item, change this license plate bulb on your Toyota Matrix without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Toyota Matrix
To swap the one on the front plate, nothing could be simpler, you will have to position yourself under the automobile (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally held by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Take out the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to put in too much pressure or you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.
How to swap the rear license plate bulb on my Toyota Matrix
Finally last possibility, you must swap the bulb on the backplate of your Toyota Matrix, but you cannot really open the cover from the outside of your automobile. In this case, here is the method to accomplish this task:
- Disconnect the battery from your Toyota Matrix
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Toyota Matrix, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main tactics for changing license plate bulbs on your car, bear in mind that on some models the technique may be a bit different but you should be able to realize it following the explanation of this content page. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Toyota Matrix. If you wish to change other bulbs like the position light bulbs on your Toyota Matrix or the low beam bulbs on Toyota Matrix, don’t be reluctant to consult our articles which explain you the process to follow.
To find more tips on the Toyota Matrix, take a look at the Toyota Matrix category.
