It doesn’t matter if it’s for your own personal safety, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are always functional is fundamental. In fact, bulbs are wearing auto parts that will obviously burn out over time and as a result need to be replaced. You’re likely on the website because one of your parking lights is burnt out and you’re wondering how to change your Toyota Land Cruiser Serie 90’s license plate bulb, we’ve written this content to help you do it all on your own and not have to go to your auto technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Toyota Land Cruiser Serie 90.
How to swap the license plate bulb on your Toyota Land Cruiser Serie 90 throughout the outside
This method is the least difficult of the two, actually, for this one you will simply require to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will take a moment on in the second part of this article to clarify the method.
So let’s begin with changing the number plate bulb by going through the outside of your Toyota Land Cruiser Serie 90. It doesn’t matter if it’s the front or the back of your automobile the technique will be similar.
Here are a few simple actions to follow to carry out this service:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Land Cruiser Serie 90
- Use your screwdriver or knife to eject the bulb from its place, if you are worried of damaging something, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the achievement of the operation.
.
How to replace the number plate bulb on your Toyota Land Cruiser Serie 90 without outside access
Second part of our item, change this license plate bulb on your Toyota Land Cruiser Serie 90 without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Toyota Land Cruiser Serie 90
To swap the one on the front plate, nothing could be much easier, you will have to put yourself under the automobile (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at the same time, then once you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to exert too much force otherwise you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.
How to swap the rear license plate bulb on my Toyota Land Cruiser Serie 90
Finally last solution, you must swap the bulb on the backplate of your Toyota Land Cruiser Serie 90, but you cannot open the cover from the outside of your automobile. In this case, here is the method to carry out this operation:
- Unplug the battery from your Toyota Land Cruiser Serie 90
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Toyota Land Cruiser Serie 90, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main ways for changing license plate bulbs on your car, bear in mind that on some models the technique may be a bit different but you should be able to do it following the outline of this article. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Toyota Land Cruiser Serie 90. If you want to change other bulbs like the position light bulbs on your Toyota Land Cruiser Serie 90 or the low beam bulbs on Toyota Land Cruiser Serie 90, don’t hesitate to read our articles which demonstrate you the procedure to follow.
To get more tips on the Toyota Land Cruiser Serie 90, take a look at the Toyota Land Cruiser Serie 90 category.
