Regardless whether it’s for your personal safety, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are all the time working is very important. Indeed, bulbs are wearing parts that will undoubtedly burn out in the future and as a result need to be changed. You’re most certainly in this article because one of your parking lights is burnt out and you’re wondering how to change your Toyota Land Cruiser Serie 150’s license plate bulb, we’ve written and published this document to help you do it without any help and not have to go to your auto technician. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Toyota Land Cruiser Serie 150.
How to swap the license plate bulb on your Toyota Land Cruiser Serie 150 throughout the outside
This tactic is the simplest of the two, in truth, for this one you will simply have to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second part of this document to demonstrate the method.
So let’s start with replacing the number plate bulb by going through the outside of your Toyota Land Cruiser Serie 150. Regardless whether it’s the front or the back of your vehicle the process will be the same.
Here are a few simple actions to stick to to perform this routine service:
- With the engine off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Land Cruiser Serie 150
- Use your screwdriver or knife to eject the bulb from its place, if you are afraid of damaging anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the achievement of the process.
.
How to replace the number plate bulb on your Toyota Land Cruiser Serie 150 without outside access
Second part of our content, replace this license plate bulb on your Toyota Land Cruiser Serie 150 without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Toyota Land Cruiser Serie 150
To swap the one on the front plate, nothing could be much easier, you will have to position yourself under the vehicle (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take out the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to apply too much pressure otherwise you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and replace it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my Toyota Land Cruiser Serie 150
Finally last option, you must swap the bulb on the backplate of your Toyota Land Cruiser Serie 150, but you cannot open the cover from the outside of your vehicle. In this instance, here is the technique to carry out this operation:
- Disconnect the battery from your Toyota Land Cruiser Serie 150
- Locate the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Toyota Land Cruiser Serie 150, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main tactics for replacing license plate bulbs on your car, bear in mind that on some models the technique may be a bit different but you should be able to realize it following the outline of this document. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Toyota Land Cruiser Serie 150. If you desire to change other bulbs like the position light bulbs on your Toyota Land Cruiser Serie 150 or the low beam bulbs on Toyota Land Cruiser Serie 150, don’t hesitate to read our content articles which describe you the procedure to follow.
If you need more guides on the Toyota Land Cruiser Serie 150, go to our Toyota Land Cruiser Serie 150 category.
