Whether it’s for your personal safety, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are always operational is fundamental. In fact, bulbs are wearing parts that will predictably burn out after some time and as a result need to be replaced. You’re most certainly on the website because one of your parking lights is burnt out and you’re worried about how to change your Toyota Corolla’s license plate bulb, we’ve made this content to help you do it all on your own and not have to go to your auto mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Toyota Corolla.
How to change the license plate bulb on your Toyota Corolla throughout the outside
This method is the simplest of the two, actually, for this one you will only have to take out the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate a moment on in the second section of this content to explain the method.
So let’s start with changing the number plate bulb by going through the outside of your Toyota Corolla. Whether it’s the front or the back of your vehicle the technique will be the same.
Here are a few simple guidelines to follow to perform this maintenance tasks:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this purpose (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Corolla
- Use your screwdriver or knife to eject the bulb from its place, in the event you are scared of damaging a thing, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the successfulness of the operation.
.
How to replace the number plate bulb on your Toyota Corolla without outside access
Second section of our content page, change this license plate bulb on your Toyota Corolla without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Toyota Corolla
To change the one on the front plate, nothing could be much easier, you will have to position yourself under the vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to exert too much force or you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my Toyota Corolla
Finally last solution, you must change the bulb on the backplate of your Toyota Corolla, but you cannot really open the cover from the outside of your vehicle. In this case, here is the process to carry out this operation:
- Disconnect the battery from your Toyota Corolla
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Toyota Corolla, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main approaches for changing license plate bulbs on your car, take notice that on some models the method may be a bit different but you should be able to accomplish it following the explanation of this article content. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Toyota Corolla. If you wish to change other bulbs like the position light bulbs on your Toyota Corolla or the low beam bulbs on Toyota Corolla, don’t be reluctant to read our articles which explain you the procedure to follow.
If you wish more tutorials on the Toyota Corolla, go to our Toyota Corolla category.
