Whether it’s for your specific safety, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are always functional is very important. In reality, bulbs are wearing parts that will surely burn out with time and therefore need to be replaced. You’re quite likely on this site because one of your parking lights is burnt out and you’re wanting to know how to change your Toyota Aygo’s license plate bulb, we’ve written and published this content to help you do it by yourself and not have to go to your auto mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Toyota Aygo.
How to change the license plate bulb on your Toyota Aygo throughout the outside
This tactic is the most simple of the two, in reality, for this one you will only require to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second section of this document to show you the method.
So let’s begin with changing the number plate bulb by going through the outside of your Toyota Aygo. Whether it’s the front or the back of your motor vehicle the process will be the same.
Here are a few simple steps to follow to conduct this service:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Aygo
- Use your screwdriver or knife to remove the bulb from its place, if you are worried of destroying something, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the achievement of the procedure.
.
How to change the number plate bulb on your Toyota Aygo without outside access
Second section of our document, swap this license plate bulb on your Toyota Aygo without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Toyota Aygo
To change the one on the front plate, nothing could be less difficult, you will have to position yourself under the motor vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take out the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to exert too much pressure or you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to change the rear license plate bulb on my Toyota Aygo
Finally last possibility, you must change the bulb on the backplate of your Toyota Aygo, but you cannot open the cover from the outside of your motor vehicle. In such a case, here is the tactic to do this operation:
- Disconnect the battery from your Toyota Aygo
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Toyota Aygo, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main tactics for changing license plate bulbs on your car, be aware that on some models the method may be a bit different but you should be able to accomplish it following the outline of this content page. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Toyota Aygo. If you need to change other bulbs like the position light bulbs on your Toyota Aygo or the low beam bulbs on Toyota Aygo, don’t be reluctant to consult our articles which demonstrate you the operation to follow.
Whenever you have any additional questions about the Toyota Aygo, do not hesitate to consult our Toyota Aygo category.
