Regardless it’s for your specific safety, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are all the time effective is very important. In reality, bulbs are wearing parts that will predictably burn out after some time and therefore need to be swapped out. You’re almost certainly in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Toyota Aygo 2’s license plate bulb, we’ve written and published this article to help you do it all on your own and not have to go to your auto technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Toyota Aygo 2.
How to replace the license plate bulb on your Toyota Aygo 2 through the outside
This method is the quickest of the two, in reality, for this one you will simply require to take away the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second section of this article content to show you the method.
So let’s start with swapping the number plate bulb by going through the outside of your Toyota Aygo 2. Regardless it’s the front or the back of your motor vehicle the process will be identical.
Here are a few simple actions to stick to to carry out this maintenance tasks:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Aygo 2
- Use your screwdriver or knife to remove the bulb from its placement, in the event you are worried of destroying a thing, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the achievement of the operation.
.
How to change the number plate bulb on your Toyota Aygo 2 without outside access
Second section of our content, swap this license plate bulb on your Toyota Aygo 2 without external access. Generally you will be able to access it, but some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Toyota Aygo 2
To replace the one on the front plate, nothing could be much easier, you will have to put yourself under the motor vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always held by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Take away the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to exert too much force or you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and swap it with the new , then check and reassemble the whole thing.
How to replace the rear license plate bulb on my Toyota Aygo 2
Finally last possibility, you must replace the bulb on the backplate of your Toyota Aygo 2, but you simply cannot open the cover from the outside of your motor vehicle. In this case, here is the solution to operate this task:
- Disconnect the battery from your Toyota Aygo 2
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Toyota Aygo 2, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main techniques for swapping license plate bulbs on your car, bear in mind that on some models the method may be a bit different but you should be able to do it following the outline of this content page. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Toyota Aygo 2. If you desire to change other bulbs like the position light bulbs on your Toyota Aygo 2 or the low beam bulbs on Toyota Aygo 2, don’t hesitate to consult our articles which describe you the process to follow.
To find more tips on the Toyota Aygo 2, take a look at the Toyota Aygo 2 category.
