Regardless it’s for your own personal safety, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are in every case effective is fundamental. In reality, bulbs are wearing units that will undoubtedly burn out with time and consequently need to be replaced. You’re quite likely on this site because one of your parking lights is burnt out and you’re questioning how to change your Tesla Model 3’s license plate bulb, we’ve created this article content to help you do it on your own and not have to go to your motor mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Tesla Model 3.
How to replace the license plate bulb on your Tesla Model 3 through the outside
This tactic is the simplest of the two, in reality, for this one you will only have to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second section of this article to show you the way.
So let’s start with replacing the number plate bulb by going through the outside of your Tesla Model 3. Regardless it’s the front or the back of your vehicle the operation will be identical.
Here are a few simple actions to follow to perform this routine service:
- With the engine off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Tesla Model 3
- Use your screwdriver or knife to eject the bulb from its placement, in the event you are worried of breaking anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to confirm the successfulness of the procedure.
.
How to change the number plate bulb on your Tesla Model 3 without outside access
Second section of our content, swap this license plate bulb on your Tesla Model 3 without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Tesla Model 3
To replace the one on the front plate, nothing could be much easier, you will have to position yourself under the vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases held by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to exert too much force or you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and replace it with the new , then check and reassemble the whole thing.
How to replace the rear license plate bulb on my Tesla Model 3
Finally last option, you must replace the bulb on the backplate of your Tesla Model 3, but you cannot really open the cover from the outside of your vehicle. In such a case, here is the tactic to accomplish this task:
- Disconnect the battery from your Tesla Model 3
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Tesla Model 3, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main tactics for replacing license plate bulbs on your car, take note that on some models the technique may be a bit different but you should be able to do it following the explanation of this document. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Tesla Model 3. If you wish to change other bulbs like the position light bulbs on your Tesla Model 3 or the low beam bulbs on Tesla Model 3, don’t hesitate to consult our content articles which describe you the procedure to follow.
Whenever you have any additional questions about the Tesla Model 3, do not hesitate to consult our Tesla Model 3 category.
