Regardless it’s for your specific security, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are in every case functioning is very important. In fact, bulbs are wearing parts that will inevitably burn out after awhile and as a consequence need to be replaced. You’re quite likely on the website because one of your parking lights is burnt out and you’re struggling with how to change your Suzuki Alto’s license plate bulb, we’ve created this content page to help you do it all on your own and not have to go to your technician. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Suzuki Alto.
How to replace the license plate bulb on your Suzuki Alto throughout the outside
This solution is the quickest of the two, in reality, for this one you will only require to take off the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second part of this content to demonstrate the approach.
So let’s begin with swapping the number plate bulb by going through the outside of your Suzuki Alto. Regardless it’s the front or the back of your automobile the method will be the same.
Here are a few simple actions to follow to carry out this maintenance:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this goal (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Suzuki Alto
- Use your screwdriver or knife to remove the bulb from its placement, in the event that you are scared of breaking a thing, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to confirm the successfulness of the process.
.
How to replace the number plate bulb on your Suzuki Alto without outside access
Second part of our content page, replace this license plate bulb on your Suzuki Alto without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Suzuki Alto
To replace the one on the front plate, nothing could be much easier, you will have to put yourself under the automobile (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually kept by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Remove the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to put in too much pressure otherwise you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and change it with the new , then test out and reassemble the whole thing.
How to replace the rear license plate bulb on my Suzuki Alto
Finally last possibility, you must replace the bulb on the backplate of your Suzuki Alto, but you cannot open the cover from the outside of your automobile. In this instance, here is the solution to perform this task:
- Unplug the battery from your Suzuki Alto
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Suzuki Alto, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main methods for swapping license plate bulbs on your car, take notice that on some models the technique may be a bit different but you should be able to accomplish it following the outline of this content. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Suzuki Alto. If you desire to change other bulbs like the position light bulbs on your Suzuki Alto or the low beam bulbs on Suzuki Alto, don’t hesitate to browse our articles which explain you the process to follow.
If you wish more guides on the Suzuki Alto, go to our Suzuki Alto category.
